ISO 295:2004
Current
Current
The latest, up-to-date edition.
Plastics — Compression moulding of test specimens of thermosetting materials
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English, French
Published date
01-14-2004
ISO 295:2004 establishes the general principles and lays down the procedure to prepare test specimens of heat- and pressure-moulded thermosetting material from different moulding compounds, specifies the details for test specimen preparation to be included with the test reports on properties and gives the general principles for the design of the mould intended for the preparation of the test specimens. The method applies to phenolic resin, aminoplastic, melamine/phenol, epoxy and unsaturated polyester-based thermosetting powder moulding compounds (PMCs). Special methods for preparing test specimens required because of the nature of certain moulding compounds, their flow properties or other variable factors, are not considered.
| DevelopmentNote |
Supersedes ISO/DIS 295 (01/2004)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 295:2004-05 | Identical |
| NF EN ISO 295 : 2004 | Identical |
| NBN EN ISO 295 : 2004 | Identical |
| NEN EN ISO 295 : 2004 | Identical |
| I.S. EN ISO 295:2004 | Identical |
| PN EN ISO 295 : 2006 | Identical |
| SN EN ISO 295 : 2004 | Identical |
| UNI EN ISO 295 : 2005 | Identical |
| BIS IS 13360-2-2 : 2013 | Identical |
| UNE-EN ISO 295:2004 | Identical |
| BS EN ISO 295:2004 | Identical |
| EN ISO 295 : 2004 | Identical |
| DIN EN ISO 295 E : 2004 | Identical |
| NEN ISO 295 : 1992 | Identical |
| BS 2782-9 Method 902A:1977 | Identical |
| DIN 53451:1972-07 | Similar to |
| BS 2782-9.902A(1992) : 1992 AMD 10344 | Identical |
| NF ISO 295 : 1992 | Identical |
| NFT 58 005 : 1977 | Similar to |
| NF EN ISO 178 : 2011 AMD 1 2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| ISO 178:2010 | Plastics Determination of flexural properties |
| 16/30334902 DC : 0 | BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS |
| DIN ISO 175:1989-04 | PLASTICS - DETERMINATION OF THE EFFECTS OF LIQUID CHEMICALS, INCLUDING WATER |
| DIN EN ISO 877-1:2016-09 (Draft) | PLASTICS - METHODS OF EXPOSURE TO SOLAR RADIATION - PART 1: GENERAL GUIDANCE |
| BS ISO 20753 : 2008 | PLASTICS - TEST SPECIMENS |
| 07/30169692 DC : 0 | BS EN 60695-2-12 - FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| 08/30188330 DC : DRAFT AUG 2008 | BS EN ISO 178 - PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| CEI 89-38 : 2014 | FIRE HAZARD TESTING - PART 11-11: TEST FLAMES - DETERMINATION OF THE CHARACTERISTIC HEAT FLUX FOR IGNITION FROM A NON-CONTACTING FLAME SOURCE |
| 14/30295041 DC : 0 | BS ISO 19095-2 - ADHESIVES - EVALUATION OF THE ADHESION INTERFACE PERFORMANCE IN PLASTIC-METAL ASSEMBLIES - PART 2: TEST SPECIMENS |
| 04/30115317 DC : 0 | BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS |
| UNE-EN ISO 877-1:2011 | Plastics - Methods of exposure to solar radiation - Part 1: General guidance (ISO 877-1:2009) |
| BIS IS 13360-5-4 : 2013 | PLASTICS - METHODS OF TESTING - PART 5: MECHANICAL PROPERTIES - SECTION 4: DETERMINATION OF IZOD IMPACT STRENGTH |
| BS 2782-4.430A.D(1983) : 1983 | METHODS OF TESTING PLASTICS - CHEMICAL PROPERTIES - DETERMINATION OF WATER AND BOILING WATER ABSORPTION AT 23 DEGREES C. DETERMINATION OF WATER AND BOILING WATER WITH ALLOWANCE OF WATER-SOLUBLE MATTER |
| NF EN 60112 : 2003 AMD 1 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| BS EN ISO 178 : 2010 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| I.S. EN 60695-11-20:2015 | FIRE HAZARD TESTING - PART 11-20: TEST FLAMES - 500 W FLAME TEST METHODS |
| I.S. EN 60112:2003 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| UNI EN ISO 6721-1 : 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| BS EN 60695-10-2:2014 | Fire hazard testing Abnormal heat. Ball pressure test method |
| DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| NF EN ISO 6721-1 : 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| BS EN ISO 6721-1:2011 | Plastics. Determination of dynamic mechanical properties General principles |
| ONORM EN ISO 6721-1 : 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| BIS IS 13360-6-18 : 2013 | PLASTICS - METHODS OF TESTING - PART 6: THERMAL PROPERTIES - SECTION 18: DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - HIGH-STRENGTH THERMOSETTING LAMINATES AND LONG-FIBRE-REINFORCED PLASTICS |
| EN ISO 178:2010/A1:2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013) |
| ASTM D 5935 : 1996 | Practice for Acquisition and Presentation of Comparable Single-Point Data (Withdrawn 1998) |
| ONORM EN ISO 11403-1 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| ASTM D 5941 : 1996 | Standard Test Method for Determination of Izod Impact Strength (Withdrawn 1998) |
| I.S. EN ISO 180:2001 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| DIN EN ISO 11403-1 E : 2003 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| DIN EN 14598-3:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| DIN EN 14598-2:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements |
| DIN EN ISO 11403-3 E : 2002 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| BS EN ISO 11248:2000 | Plastics. Thermosetting moulding materials. Evaluation of short-term performance at elevated temperatures |
| UNE-EN ISO 175:2011 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| BS EN ISO 604:2003 | Plastics. Determination of compressive properties |
| BS EN ISO 3167:2014 | Plastics. Multipurpose test specimens |
| BS EN ISO 11403-3:2014 | Plastics. Acquisition and presentation of comparable multipoint data Environmental influences on properties |
| I.S. EN ISO 11403-2:2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012) |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| EN 12576:1998 | Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC, BMC and DMC |
| DIN EN ISO 178:2013-09 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013) |
| DIN EN ISO 175:2011-03 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| DIN EN ISO 4611:2011-04 | Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist (ISO 4611:2010) |
| EN 60695-2-12:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014) |
| ONORM EN ISO 179-1 : 2010 | PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST |
| NF EN ISO 179-1 : 2010 | PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST |
| BS 2782-1.136(1994) : 1994 AMD 10687 | METHODS OF TESTING PLASTICS - THERMAL PROPERTIES - DETERMINATION OF THE SHORT-TERM PERFORMANCE OF THERMOSETTING MOULDING MATERIALS AT ELEVATED TEMPERATURES |
| SAE J 1639 : 1995(S2017) | CLASSIFICATION SYSTEM FOR AUTOMOTIVE POLYAMIDE (PA) PLASTICS |
| BS EN 60695-11-10:2013 | Fire hazard testing Test flames. 50 W horizontal and vertical flame test methods |
| 07/30171973 DC : 0 | BS EN ISO 6721-12 - PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 12: COMPRESSIVE VIBRATION - NON-RESONANCE METHOD |
| 09/30206613 DC : 0 | BS EN 60695-11-20 ED.2 - FIRE HAZARD TESTING - PART 11-20: TEST FLAMES - 500 W FLAME TEST METHODS |
| BS 771-1:1980 | Phenolic moulding materials Specification for physical properties (excluding type L2 material) |
| DIN EN ISO 178 E : 2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013) |
| 11/30258054 DC : 0 | BS EN 60243-1 - ELECTRICAL STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES |
| 05/30132990 DC : DRAFT APR 2005 | ISO 20753 - PLASTICS - TEST SPECIMENS |
| 07/30169691 DC : 0 | BS EN 60695-2-13 - FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITABILITY (GWIT) TEST METHOD FOR MATERIALS |
| 14/30253068 DC : 0 | BS EN ISO 4892-1 - PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE |
| UNI EN ISO 877-1 : 2011 | PLASTICS - METHODS OF EXPOSURE TO SOLAR RADIATION - PART 1: GENERAL GUIDANCE |
| PREN ISO 11403-1 : DRAFT 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO/DIS 11403-1:2012) |
| 08/30192288 DC : 0 | BS EN ISO 179-1 - PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST |
| BS EN 60695-2-12 : 2010 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| BS 2782-1 Method 121A and 121B:1991 | Methods of testing plastics. Thermal properties Determination of temperature of deflection of plastics under a bending stress |
| EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| EN IEC 62631-2-1:2018 | Dielectric and resistive properties of solid insulating materials - Part 2-1: Relative permittivity and dissipation factor - Technical frequencies (0,1 Hz to 10 MHz) - AC Methods |
| I.S. EN ISO 178:2010 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010) |
| I.S. EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| BIS IS 13360-3-5 : 2013 | PLASTICS - METHODS OF TESTING - PART 3: PHYSICAL AND DIMENSIONAL PROPERTIES - SECTION 5: THERMOSETTING MOULDING MATERIALS - DETERMINATION OF SHRINKAGE |
| ISO 10351:1992 | Plastics Determination of the combustibility of specimens using a 125 mm flame source |
| EN ISO 6721-1:2011 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2011) |
| CEI EN 60695-10-2 : 2015 | FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD |
| NF EN 60695-2-13 : 2011 AMD 1 2014 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS |
| DIN EN ISO 75-3:2004-09 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004) |
| DIN EN ISO 14530-2:2000-08 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999 |
| BS EN ISO 180 : 2001 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH |
| DIN EN ISO 4589-2:2016-03 (Draft) | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017) |
| UNE-EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| BS EN ISO 14528-2:2000 | Plastics. Melamine-formaldehyde powder moulding compounds (MF-PMCs) Preparation of test specimens and determination of properties |
| DIN EN ISO 6603-1:2000-10 | PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 1: NON-INSTRUMENTED IMPACT TESTING |
| BS EN 14598-2:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements |
| BS EN ISO 14125 : 1998 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES |
| I.S. EN ISO 3167:2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| I.S. EN ISO 11403-1:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| I.S. EN ISO 75-3:2004 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 3: HIGH-STRENGTH THERMOSETTING LAMINATES AND LONG-FIBRE-REINFORCED PLASTICS |
| I.S. EN ISO 4611:2010 | PLASTICS - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| I.S. EN ISO 527-2:2012 | PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 2: TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS (ISO 527-2:2012) |
| I.S. EN ISO 179-1:2010 | PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST |
| I.S. EN ISO 4589-2:2017 | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017) |
| I.S. EN ISO 8256:2004 | PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH |
| I.S. EN ISO 4892-1:2016 | PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016) |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| I.S. EN ISO 11403-3:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| I.S. EN ISO 604:2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| DIN EN ISO 877-1:2011-03 | Plastics - Methods of exposure to solar radiation - Part 1: General guidance (ISO 877-1:2009) |
| I.S. EN ISO 183:1999 | PLASTICS - QUALITATIVE EVALUATION OF THE BLEEDING OF COLORANTS |
| I.S. EN ISO 175:2010 | PLASTICS - METHODS OF TEST FOR THE DETERMINATION OF THE EFFECTS OF IMMERSION IN LIQUID CHEMICALS |
| OVE/ONORM EN 60695-2-12 : 2015 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010 + A1:2014) |
| NBR IEC 60695-2-12 : 2013 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| BS 2782-5.540D(1999) : 1999 AMD 13148 | METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - GENERAL GUIDANCE |
| NBR IEC 60695-2-13 : 2013 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS |
| OVE/ONORM EN 60695-2-13 : 2015 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010 + A1:2014) |
| BS 2782-8.830A(1999) : 1999 AMD 13097 | METHODS OF TESTING PLASTICS - OTHER PROPERTIES - METHODS OF TEST FOR THE DETERMINATION OF THE EFFECTS OF IMMERSION IN LIQUID CHEMICALS |
| ONORM EN ISO 11403-2 : 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012) |
| 02/121542 DC : DRAFT MAR 2002 | ISO/DIS 11403-2 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES |
| BS EN 60695-2-13 : 2010 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS |
| DIN 7708-8:1992-02 | PLASTICS - POURABLE THERMOSETTING MOULDING MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 17/30368428 DC : 0 | BS ISO 15314 - PLASTICS - METHODS FOR MARINE EXPOSURE |
| BS ISO 11403-2 : 95 AMD 10691 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - THERMAL AND PROCESSING PROPERTIES |
| NF EN 60695-2-12 : 2011 AMD 1 2014 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| 06/30148148 DC : DRAFT MAR 2006 | EN ISO 2577 - PLASTICS - THERMOSETTING MOULDING MATERIALS - DETERMINATION OF SHRINKAGE |
| BS ISO 15314:2004 | Plastics. Methods for marine exposure |
| BS 2782-1.121D(1994) : 1994 AMD 8645 | METHODS OF TESTING PLASTICS - THERMAL PROPERTIES - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD AT HIGH-STRENGTH THERMOSETTING LAMINATES AND LONG-FIBRE-REINFORCED PLASTICS |
| I.S. EN 60695-2-13:2010 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS |
| 12/30230305 DC : 0 | BS EN 60695-10-2 ED 3.0 - FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST |
| BS 2782-3 Method 359:1984 | Methods of testing plastics. Mechanical properties Determination of Charpy impact strength of rigid materials (Charpy impact flexural test) |
| BS ISO 4589-2 : 1996 AMD 10627 | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - AMBIENT-TEMPERATURE TEST |
| BS 2782-1 Method 141:1986 | Methods of testing plastics. Thermal properties Determination of flammability by oxygen index |
| BS 2782-3.354A&B(1991) : 1991 AMD 8635 | METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF TENSILE-IMPACT STRENGTH |
| BS 2782-1:Method 140C:1993 | Methods of testing plastics. Thermal properties Determination of the combustibility of specimens using a 125 mm flame source |
| 02/120706 DC : DRAFT FEB 2002 | BS EN ISO 8256 - PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH |
| UNE-ISO 1268-8:2012 | Fibre-reinforced plastics. Methods of producing test plates. Part 8: Compression moulding of SMC and BMC |
| UNE-EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| UNE-ISO 2577:2014 | Plastics. Thermosetting moulding materials. Determination os shrinkage |
| I.S. EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013 (EQV)) |
| I.S. EN ISO 877-1:2010 | PLASTICS - METHODS OF EXPOSURE TO SOLAR RADIATION - PART 1: GENERAL GUIDANCE |
| I.S. EN 60695-10-2:2014 | FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD |
| ONORM EN ISO 20753 : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| BIS IS 13360-2-5 : 2013 | PLASTICS - METHODS OF TESTING - PART 2: SAMPLING AND PREPARATION OF TEST SPECIMENS - SECTION 5: MULTIPURPOSE TEST SPECIMENS |
| BS 2782-5 Method 550A:1981 | Methods of testing plastics. Optical and colour properties, weathering Methods of exposure to natural weathering |
| I.S. EN IEC 62631-2-1:2018 | DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 2-1: RELATIVE PERMITTIVITY AND DISSIPATION FACTOR - TECHNICAL FREQUENCIES (0,1 HZ TO 10 MHZ) - AC METHODS |
| UNI EN ISO 178 : 2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| I.S. EN 60695-11-10:2013 | FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS (IEC 60695-11-10:2013 (EQV)) |
| BS EN ISO 20753:2014 | Plastics. Test specimens |
| ASTM D 5936 : 1996 | Specification for Multipurpose Test Specimens (Withdrawn 1998) |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| UNI EN ISO 11403-1 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| EN ISO 14125:1998/A1:2011 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES |
| IEC 62631-2-1:2018 | Dielectric and resistive properties of solid insulating materials - Part 2-1: Relative permittivity and dissipation factor - Technical Frequencies (0,1 Hz - 10 MHz) - AC Methods |
| EN 60695-2-13:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014) |
| DIN EN ISO 4589-2 E : 2017 | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017) |
| DIN EN ISO 8256:2005-05 | Plastics - Determination of tensile-impact strength (ISO 8256:2004); German version EN ISO 8256:2004 |
| DIN EN ISO 11403-3:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| DIN EN ISO 11403-1:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| BS EN ISO 6603-1:2000 | Plastics. Determination of multi-axial impact behaviour of rigid plastics Non-instrumented impact testing |
| DIN EN ISO 180:2013-08 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000 + AMD.1:2006 + AMD.2:2013) |
| BS EN ISO 8256:2004 | Plastics. Determination of tensile-impact strength |
| ISO 14125:1998 | Fibre-reinforced plastic composites Determination of flexural properties |
| UNE-EN ISO 11403-2:2012 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
| BS EN ISO 11403-2:2012 | Plastics. Acquisition and presentation of comparable multipoint data Thermal and processing properties |
| IEC 60695-2-13:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials |
| UNI EN ISO 180 : 2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH |
| UNI EN ISO 3167 : 2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS |
| UNI EN ISO 14125 : 2011 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES |
| UNI EN ISO 4611 : 2011 | PLASTICS - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| UNI EN ISO 11403-2 : 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES |
| EN ISO 4611:2010 | Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist (ISO 4611:2010) |
| I.S. EN ISO 14125:1998 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES |
| BS 2782-3.335A(1993) : AMD 8638 | METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF FLEXURAL PROPERTIES |
| UNI EN ISO 604 : 2008 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| UNI EN ISO 175 : 2010 | PLASTICS - METHODS OF TEST FOR THE DETERMINATION OF THE EFFECTS OF IMMERSION IN LIQUID CHEMICALS |
| UNI EN ISO 527-2 : 2012 | PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 2: TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS |
| UNI EN ISO 179-1 : 2010 | PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST |
| DD IEC/TS 60695-2-20:2004 | Fire hazard testing Glowing/hot wire based test methods - Hot-wire coil ignitability. Apparatus, test method and guidance |
| BS EN ISO 2818 : 1997 | PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING |
| 16/30319043 DC : 0 | BS EN ISO 4589-2 - PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST |
| 09/30206609 DC : 0 | BS EN 60695-11-10 ED.2 - FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS |
| ISO 20753:2008 | Plastics Test specimens |
| 12/30255180 DC : 0 | BS EN ISO 11403-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| 02/121868 DC : DRAFT APR 2002 | BS ISO 15314 - PLASTICS - METHODS FOR MARINE EXPOSURE |
| BIS IS 2824 : 2007 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| BS 2782-1:Method 140A:1992 | Methods of testing plastics. Thermal properties Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| 11/30211730 DC : 0 | BS ISO 9352 - PLASTICS - DETERMINATION OF RESISTANCE TO WEAR BY ABRASIVE WHEELS |
| BS ISO 9352:2012 | Plastics. Determination of resistance to wear by abrasive wheels |
| BS EN ISO 877-1:2010 | Plastics. Methods of exposure to solar radiation General guidance |
| BS EN 60243-1:2013 | Electric strength of insulating materials. Test methods Tests at power frequencies |
| BS EN 60112 : 2003 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| 11/30234454 DC : 0 | BS EN ISO 6721-1 - PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| BS 2782-8 Method 830A:1986 | Methods of testing plastics. Other properties Determination of the effects of liquid chemicals, including water |
| 17/30335677 DC : 0 | BS EN ISO 178 - PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| BS EN 60695-11-20:2015 | Fire hazard testing Test flames. 500 W flame test methods |
| EN ISO 2818:1996 | PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING |
| UNI EN ISO 20753 : 2014 | PLASTICS - TEST SPECIMENS |
| DIN EN ISO 6721-1:2011-08 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| CEI EN 60243-1 : 2014 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES |
| EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| ISO 6721-12:2009 | Plastics Determination of dynamic mechanical properties Part 12: Compressive vibration Non-resonance method |
| ISO 6721-1:2011 | Plastics Determination of dynamic mechanical properties Part 1: General principles |
| IEC TS 60695-11-11:2016 | Fire hazard testing - Part 11-11: Test flames - Determination of the characteristic heat flux for ignition from a non-contacting flame source |
| EN ISO 180:2000/A2:2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013) |
| UNI EN ISO 11403-3 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| DIN EN ISO 14125:2011-05 | Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998 + Cor 1:2001 + Amd 1:2011) |
| DIN EN ISO 4892-1:2016-10 | PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016) |
| DIN EN ISO 175 E : 2011 | PLASTICS - METHODS OF TEST FOR THE DETERMINATION OF THE EFFECTS OF IMMERSION IN LIQUID CHEMICALS |
| DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| DIN EN ISO 604 E : 2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| ISO 4892-1:2016 | Plastics Methods of exposure to laboratory light sources Part 1: General guidance |
| BS EN ISO 14529-2:2000 | Plastics. Melamine/phenolic powder moulding compounds (MP-PMCs) Preparation of test specimens and determination of properties |
| UNE-EN ISO 179-1:2011 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| BS EN ISO 4589-2:2017 | Plastics. Determination of burning behaviour by oxygen index Ambient-temperature test |
| DIN EN ISO 604:2003-12 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| BS EN 12576:1998 | Plastics. Fibre reinforced composites. Preparation of compression moulded test plates of SMC, BMC and DMC |
| ISO 14528-2:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
| ISO 179:1993 | Plastics Determination of Charpy impact strength |
| BS EN ISO 4892-1:2016 | Plastics. Methods of exposure to laboratory light sources General guidance |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| UNE-EN ISO 4589-2:2017 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:2017) |
| ISO 14530-2:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| ISO 877-1:2009 | Plastics — Methods of exposure to solar radiation — Part 1: General guidance |
| ISO 4611:2010 | Plastics Determination of the effects of exposure to damp heat, water spray and salt mist |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| ISO 14529-2:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| IEC 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| BS EN ISO 75-3:2004 | Plastics. Determination of temperature of deflection under load High-strength thermosetting laminates and long-fibre-reinforced plastics |
| BS EN ISO 14527-2:2000 | Preparation of test specimens and determination of properties |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
| ISO 10350:1993 | Plastics Acquisition and presentation of comparable single-point data |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| ISO 6603-1:2000 | Plastics Determination of puncture impact behaviour of rigid plastics Part 1: Non-instrumented impact testing |
| BS EN 14598-3:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements |
| UNE-EN ISO 14125:1999 | FIBRE-REINFORCED PLASTICS COMPOSITES. DETERMINATION OF FLEXURAL PROPERTIES (ISO 14125:1998) |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| BS EN ISO 183:2000 | Plastics. Qualitative evaluation of the bleeding of colorants |
| ISO 14526-2:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 179-1:2010 | Plastics. Determination of Charpy impact properties Non-instrumented impact test |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| UNE-EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| UNE-EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| UNE-EN 60695-11-20:2016 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test methods |
| UNE-EN 60695-11-10:2014 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| BS EN ISO 11403-1:2014 | Plastics. Acquisition and presentation of comparable multipoint data Mechanical properties |
| BS EN ISO 14526-2:2000 | Plastics. Phenolic powder moulding compounds (PF-PMCs) Preparation of test specimens and determination of properties |
| UNE-EN ISO 4892-1:2017 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| EN ISO 4892-1:2016 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| EN ISO 11403-2:2012 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
| EN ISO 15252-2 : 1999 | PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 14598-2:2005/AC:2006 | REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS |
| EN ISO 14529-2 : 1999 | PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| EN ISO 11248 : 1999 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures (ISO 11248:1993) |
| EN ISO 10350-1:2017 | Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017) |
| EN ISO 877-1:2010 | Plastics - Methods of exposure to solar radiation - Part 1: General guidance (ISO 877-1:2009) |
| EN ISO 14530-2 : 1999 | PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 604 : 2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES (ISO 604:2002) |
| EN ISO 14528-2 : 1999 | PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| EN ISO 75-3:2004/AC:2006 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004) |
| EN ISO 6603-1 : 2000 | PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 1: NON-INSTRUMENTED IMPACT TESTING |
| EN ISO 4589-2:2017 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:2017) |
| EN 14598-3:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| EN ISO 175:2010 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| EN ISO 183 : 1999 | PLASTICS - QUALITATIVE EVALUATION OF THE BLEEDING OF COLORANTS |
| EN ISO 14527-2 : 1999 | PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 10350-1:2017 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017) |
| PREN ISO 6721-1 : DRAFT 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| ISO 19095-2:2015 | Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Part 2: Test specimens |
| BS ISO 11403-1 : AMD 10683 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - MECHANICAL PROPERTIES |
| BS 2782-3 Method 370:1990 | Methods of testing plastics. Mechanical properties Determination of resistance to wear by abrasive wheels |
| BS ISO 19095-2:2015 | Plastics. Evaluation of the adhesion interface performance in plastic-metal assemblies Test specimens |
| BS 2782-5:Method 540D:1995 | Methods of testing plastics. Optical and colour properties, weathering Methods of exposure to laboratory light sources. General guidance |
| UNE-EN 60695-2-13:2011 | Fire hazard testing -- Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials |
| BIS IS 13360-5-8 : 2013 | PLASTICS - METHODS OF TESTING - PART 5: MECHANICAL PROPERTIES - SECTION 8: DETERMINATION OF COMPRESSIVE PROPERTIES |
| 07/30127284 DC : 0 | BS EN ISO 4892-1 - PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE |
| BS ISO 1268-8:2004 | Fibre-reinforced plastics. Methods of producing test plates Compression moulding of SMC and BMC |
| XP T51 224-1 : 1991 XP | PLASTICS - DETERMINATION OF THE THERMAL STABILITY BY OVER DRYING (FLOATING PLATEN CHAMBER) - PART 1: GENERAL |
| ASTM D 5942 : 1996 | Test Method for Determination of Charpy Impact Strength (Withdrawn 1998) |
| BS 2782-5.542A(1979) : AMD 10684 | METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - QUALITATIVE EVALUATION OF BLEEDING COLOURANTS |
| I.S. EN 60695-2-12:2010 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| ASTM D 5943 : 1996 | Test Method for Determination of Flexural Properties (Withdrawn 1998) |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| I.S. EN ISO 6721-1:2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| ISO 15314:2004 | Plastics Methods for marine exposure |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| UNE-EN 60695-2-12:2011 | Fire hazard testing -- Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials |
| ISO 9352:2012 | Plastics — Determination of resistance to wear by abrasive wheels |
| UNE-EN ISO 6721-1:2012 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2011) |
| BS EN ISO 10350-1:2017 | Plastics. Acquisition and presentation of comparable single-point data Moulding materials |
| ASTM D 5937 : 1996 | Standard Test Method for Determination of Tensile Properties and Test Conditions for Moulding and Extrusion Plastics (Withdrawn 1998) |
| ONORM EN ISO 178 : 2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD 1:2013) |
| ONORM EN ISO 11403-3 : 2015 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| UNE-EN ISO 20753:2015 | Plastics - Test specimens (ISO 20753:2008) |
| ISO 1268-8:2004 | Fibre-reinforced plastics — Methods of producing test plates — Part 8: Compression moulding of SMC and BMC |
| DIN EN ISO 179-1:2010-11 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| DIN EN ISO 11403-2 E : 2013 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012) |
| ISO 11248:1993 | Plastics — Thermosetting moulding materials — Evaluation of short-term performance at elevated temperatures |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 15252-2:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 527-2:1996 | Plastics. Determination of tensile properties Test conditions for moulding and extrusion plastics |
| BS EN ISO 4611:2010 | Plastics. Determination of the effects of exposure to damp heat, water spray and salt mist |
| BS EN ISO 175:2010 | Plastics. Methods of test for the determination of the effects of immersion in liquid chemicals |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 14527-2:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 14530-2:2000 | Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs) Preparation of test specimens and determination of properties |
| BS EN ISO 15252-2:2000 | Plastics. Epoxy powder moulding compounds (EP-PMCs) Preparation of test specimens and determination of properties |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| DIN EN ISO 11403-2:2013-01 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
| DIN EN ISO 11403-3:2002-02 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| DIN EN ISO 527-2:2012-06 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| DIN EN ISO 11403-1:2003-09 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| DIN EN ISO 4892-1:2001-09 | PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016) |
| BS 2782-3.359(1993) : 1993 AMD 8643 | METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF CHARPY IMPACT STRENGTH |
| BS 2782-3.345A(1993) : 1993 AMD 8637 | METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF COMPRESSIVE PROPERTIES |
| BS 2782-9.931A(1993) : 1993 AMD 8626 | METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - PREPARATION AND USE OF MULTIPURPOSE TEST SPECIMENS |
| BS 2782-3.350(1993) : 1993 AMD 8641 | METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF IZOD IMPACT STRENGTH |
| BS 2782-5.551A(1988) : 1988 AMD 10820 | METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| BS 7008-1(1994) : AMD 8821 | ACQUISITION AND PRESENTATION OF COMPARABLE DATA FOR BASIC PROPERTIES OF PLASTICS - METHOD FOR SINGLE POINT DATA |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 14526-1:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 14528-2:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 14529-3:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 14529-1:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 1: Designation system and basis for specifications |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| ISO 14530-1:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications |
| ISO 14530-3:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| ISO 14526-2:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 472:2013 | Plastics Vocabulary |
| ISO 14526-3:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 14528-1:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| ISO 14527-3:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 14527-1:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 14529-2:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| ISO 15252-1:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 1: Designation system and basis for specifications |
| ISO 15252-3:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 15252-2:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 14530-2:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 14528-3:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 14527-2:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
US$73.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
Hardcopy - French
PDF - French
PDF 3 Users - French
PDF 5 Users - French
PDF 9 Users - French
Hardcopy - English
PDF - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
Hardcopy - French
PDF - French
PDF 3 Users - French
PDF 5 Users - French
PDF 9 Users - French
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.