JIS C 1010-1:2014

Introduction1 Scope and object 1.1 Scope 1.2 Object 1.3 Verification 1.4 Environmental conditions2 Normative references3 Terms and definitions 3.1 Equipment and states of equipment 3.2 Parts and accessories 3.3 Electrical quantities 3.4 Tests 3.5 Safety terms 3.6 Insulation4 Tests 4.1 General 4.2 Sequence of tests 4.3 Reference test conditions 4.4 Testing in SINGLE FAULT CONDITION5 Marking and documentation 5.1 Marking 5.2 Warning markings 5.3 Durability of markings 5.4 Documentation6 Protection against electric shock 6.1 General 6.2 Determination of ACCESSIBLE parts 6.3 Permissible limits for ACCESSIBLE parts 6.4 Protection in NORMAL CONDITION 6.5 Protection in SINGLE FAULT CONDITION 6.6 Connections to external circuits 6.7 CLEARANCES and CREEPAGE DISTANCES 6.8 Procedure for dielectric strength tests 6.9 Constructional requirements for protection against electric shock 6.10 Connection to MAINS supply source and connections between parts of equipment 6.11 Disconnection from supply source7 Protection against mechanical HAZARDS 7.1 General 7.2 Moving parts 7.3 Stability 7.4 Provisions for lifting and carrying 7.5 Wall mounting 7.6 Expelled parts8 Mechanical resistance to shock and impact 8.1 ENCLOSURE rigidity test 8.2 Drop test9 Protection against the spread of fire 9.1 Eliminating or reducing the sources of ignition within the equipment 9.2 Containment of fire within the equipment, should it occur 9.3 Limited-energy circuit 9.4 Requirements for equipment containing or using flammable liquids 9.5 Overcurrent protection10 Equipment temperature limits and resistance to heat 10.1 Surface temperature limits for protection against burns 10.2 Temperatures of windings 10.3 Other temperature measurements 10.4 Conduct of temperature tests 10.5 Resistance to heat11 Protection against HAZARDS from fluids 11.1 General 11.2 Cleaning 11.3 Spillage 11.4 Overflow 11.5 Battery electrolyte 11.6 Specially protected equipment 11.7 Fluid pressure and leakage12 Protection against radiation, including laser sources, and against sonic and ultrasonic pressure 12.1 General 12.2 Equipment producing ionizing radiation 12.3 Ultraviolet (UV) radiation 12.4 Microwave radiation 12.5 Sonic and ultrasonic pressure 12.6 Laser sources13 Protection against liberated gases, explosion and implosion 13.1 Poisonous and injurious gases 13.2 Explosion and implosion14 Components 14.1 General 14.2 Motors 14.3 Overtemperature protection devices 14.4 Fuse holders 14.5 MAINS voltage selecting devices 14.6 HIGH INTEGRITY components 14.7 MAINS transformers tested outside equipment 14.8 Printed circuit boards 14.9 Circuits or components used as transient overvoltage limiting devices15 Protection by interlocks 15.1 General 15.2 Prevention of reactivating 15.3 Reliability16 Test and measurement equipment 16.1 Current measuring circuits 16.2 Multifunction meters and similar equipmentAnnex A (normative) - Measuring circuits for ACCESSIBLE currentAnnex B (normative) - Standard test fingerAnnex C (normative) - Measurement of CLEARANCES and CREEPAGE DISTANCESAnnex D (normative) - Parts between which insulation requirements are specifiedAnnex E (normative) - Reduction of POLLUTION degreesAnnex F (normative) - ROUTINE TESTSAnnex G (informative) - Leakage and rupture from fluids under pressureAnnex H (informative) - Index of defined termsAnnex 1 (informative) - Comparison table between JIS and corresponding International StandardBibliography