• MMPDS 04 : 2008 CHG NT 1 2009

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    METALLIC MATERIALS PROPERTIES DEVELOPMENT AND STANDARDIZATION (MMPDS)

    Available format(s): 

    Superseded date:  04-01-2010

    Language(s): 

    Published date:  01-12-2013

    Publisher:  Metallic Materials Properties Development Standardization

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Chapter 1
    1.0 General
    1.1 Purpose and Use of Document
    1.2 Nomenclature
    1.3 Commonly Used Formulas
    1.4 Basic Principles
    1.5 Types of Failures
    1.6 Columns
    1.7 Thin-Walled and Stiffened Thin-Walled Sections
    References
    Chapter 2
    2.0 Steel
    2.1 General
    2.2 Carbon Steels
    2.3 Low-Alloy Steels (AISI Grades and Proprietary Grades)
    2.4 Intermediate Alloy Steels
    2.5 High-Alloy Steels
    2.6 Precipitation- and Transformation-Hardening Steels
         (Stainless)
    2.7 Austenitic Stainless Steels
    2.8 Element Properties
    References
    Chapter 3
    3.0 Aluminum
    3.1 General
    3.2 2000 Series Wrought Alloys
    3.3 3000 Series Wrought Alloys
    3.4 4000 Series Wrought Alloys
    3.5 5000 Series Wrought Alloys
    3.6 6000 Series Wrought Alloys
    3.7 7000 Series Wrought Alloys
    3.8 200.0 Series Cast Alloys
    3.9 300.0 Series Cast Alloys
    3.10 Element Properties
    References
    Chapter 4
    4.0 Magnesium Alloys
    4.1 General
    4.2 Magnesium-Wrought Alloys
    4.3 Magnesium Cast Alloys
    4.4 Element Properties
    References
    Chapter 5
    5.0 Titanium
    5.1 General
    5.2 Unalloyed Titanium
    5.3 Alpha and Near-Alpha Titanium Alloys
    5.4 AlphBeta Titanium Alloys
    5.5 Beta, Near-Beta, and Metastable-Beta Titanium Alloys
    5.6 Element Properties
    References
    Chapter 6
    6.0 Heat-Resistant Alloys
    6.1 General
    6.2 Iron-Chromium-Nickel-Base Alloys
    6.3 Nickel-Base Alloys
    6.4 Cobalt-Base Alloys
    References
    Chapter 7
    7.0 Miscellaneous Alloys and Hybrid Materials
    7.1 General
    7.2 Beryllium
    7.3 Copper and Copper Alloys
    7.4 Multiphase Alloys
    7.5 Aluminum Alloy Sheet Laminates
    References
    Chapter 8
    8.0 Structural Joints
    8.1 Mechanically Fastened Joints
    8.2 Metallurgical Joints
    8.3 Bearings, Pulleys, and Wire Rope
    References
    Chapter 9
    9.0 Index
    Cross Index Table for Chapter 9
    9.1 General
    9.2 Material, Specification, Testing, and Data Requirements
    9.3 Submission of Data
    9.4 Substantiation of Properties
    9.5 Analysis Procedures for Statistically Computed Minimum
         Static Properties
    9.6 Analysis Procedures for Dynamic and Time Dependent Properties
    9.7 Analysis Procedures for Structural Joint Properties
    9.8 Examples of Data Analysis and Data Presentation for
         Static Properties
    9.9 Examples of Data for Dynamic and Time Dependent Properties
    9.10 Statistical Tables
    References
    Appendices
    A.0 Glossary
    A.1 Abbreviations
    A.2 Symbols
    A.3 Definitions
    A.4 Conversion of U.S. Units of Measure Used in MMPDS to SI Units
    B.0 Alloy Index
    C.0 Specification Index
    D.0 Testing Standards
    E.0 Subject Index

    Abstract - (Show below) - (Hide below)

    Describes a source of design mechanical and physical properties and joint allowables.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes MMPDS 03. Includes 9 Chapters & Change Notice 1 (2009). Also available in CD and Electronic Format. (08/2008) CHANGE NOTICE is also available seperately. (10/2009)
    Document Type Standard
    Publisher Metallic Materials Properties Development Standardization
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN ISO 20312:2011 Petroleum and natural gas industries. Design and operating limits of drill strings with aluminium alloy components
    I.S. EN ISO 20312:2011 PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATING LIMITS OF DRILL STRINGS WITH ALUMINIUM ALLOY COMPONENTS (ISO 20312:2011)
    ISO 20312:2011 Petroleum and natural gas industries Design and operating limits of drill strings with aluminium alloy components
    NASA JSC 27301 : 2009 MATERIALS AND PROCESSES SELECTION, CONTROL, AND IMPLEMENTATION PLAN FOR JSC FLIGHT HARDWARE
    EN ISO 20312 : 2011 PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATING LIMITS OF DRILL STRINGS WITH ALUMINIUM ALLOY COMPONENTS (ISO 20312:2011)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective