• There are no items in your cart

NF EN 201 : 2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS AND RUBBER MACHINES - INJECTION MOULDING MACHINES - SAFETY REQUIREMENTS
Superseded date

11-01-2021

Published date

01-12-2013

Avant-propos
Introduction
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Liste des phénomènes dangereux significatifs
5 Prescriptions de sécurité et mesures de prévention
6 Vérification des prescriptions de sécurité et/ou mesures
  de prévention
7 Informations pour l'utilisation
Annexe A (normative) - Protecteur mobile avec dispositif de
         verrouillage de type I (axe non électrique)
Annexe B (normative) - Protecteur mobile avec dispositif de
         verrouillage de type II (axe non électrique)
Annexe C (normative) - Protecteur mobile avec dispositif de
         verrouillage de type III (axe non électrique)
Annexe D (normative) - Protecteurs mobiles avec dispositif
         de verrouillage de type I (axe électrique)
Annexe E (normative) - Protecteurs mobiles avec dispositif
         de verrouillage de type II (axe électrique)
Annexe F (normative) - Protecteurs mobiles avec dispositif
         de verrouillage de type III (axe électrique)
Annexe G (normative) - Équipement de protection
         électro-sensible en forme de rideau lumineux
Annexe H (normative) - Dispositif de commande bimensuelle
Annexe J (normative) - Systèmes d'acquittement
Annexe K (normative) - Code d'essai acoustique
Annexe L (informative) - Panneaux d'avertissement
Annexe M (normative) - Utilisation de distributeurs
         proportionnels pour la commande des
         mouvements du plateau
Annexe ZA (informative) - Relation entre la présente Norme
          européenne et les exigences essentielles de la
          Directive 98/37/CE
Annexe ZB (informative) - Relation entre la présente Norme
          européenne et les exigences essentielles de la
          Directive 2006/42/CE
Bibliographie

Defines the essential safety requirements for injection moulding machines for processing plastics and/or rubber. Defines safety requirements for interaction between injection moulding machines and ancillary equipment, but not the safety requirements of the ancillary equipment, or design requirements for an exhaust system. Applicable to those machines made after the standard issue date.

DevelopmentNote
Supersedes NFE 63 600, NFE 63 601, NFE 63 602 and NFE 63 604 (08/2001) Indice de classement: E63-600. (12/2005) PR NF EN 201 February 2008. (02/2008)
DocumentType
Standard
PublisherName
Association Francaise de Normalisation
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NBN EN 201 : 2010 Identical
NEN EN 201 : 2009 Identical
NS EN 201 : 2009 Identical
I.S. EN 201:2009 Identical
SN EN 201 : 2010 Identical
UNI EN 201 : 2010 Identical
UNE-EN 201:2010 Identical
BS EN 201:2009 Identical
EN 201:2009 Identical
DIN EN 201:2010-02 Identical

IEC 61000-6-4:2006+AMD1:2010 CSV ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
CLC/TS 61496-2:2006 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
EN 999:1998+A1:2008 Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 1760-1:1997+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN 574:1996+A1:2008 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
CLC/TS 61496-3:2008 Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN ISO 3747:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010)
EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
EN 61000-6-2:2005/corrigendum:2005 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
IEC 61496-3:2008 Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
EN 61000-6-4:2007/A1:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN ISO 14122-4:2016 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
EN ISO 14122-2:2016 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 1760-2:2001+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
IEC 61496-2:2013 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.