NF EN 777-2 : 2009

Superseded

View Superseded by

MULTI-BURNER GAS-FIRED OVERHEAD RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - PART 2: SYSTEM E - SAFETY

Superseded date

10-05-2021

Published date

01-12-2013

Publisher

Association Francaise de Normalisation

Avant-propos
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Classification des systèmes
5 Exigences de construction
6 Exigences de fonctionnement
7 Méthodes d'essais
8 Marquage et notices
9 Évaluation de la conformité des POCED et de leurs
  terminaux associés
Annexe A (informative) Situations nationales
Annexe B (informative) Système E
Annexe C (informative) Règles d'équivalence
Annexe D (informative) Calcul du débit massique des
         produits de combustion
Annexe E (informative) Identification des types de gaz
         utilisés dans les différents pays
Annexe F (normative) Conditions nationales spécifiques
Annexe G (informative) Exemple de calcul des facteurs
         de pondération pour un appareil à plusieurs
         allures
Annexe H (informative) Calcul de conversions de NOx
Annexe I (informative) Situations dans les pays dont les
         organismes nationaux sont membres associés du CEN
Annexe J (informative) Modèle de plans d'échantillonnage
Annexe K (informative) Détermination des pertes parles
         fumées
Annexe ZA (informative) Articles de la présente Norme
          européenne traitant des exigences essentielles
          ou d'autres dispositions de Directives UE
Annexe ZB (informative) Articles de la présente Norme
          européenne concernant les dispositions de la
          Directive UE Produits de construction
Bibliographie

Specifies the requirements and test methods for the construction, safety, classification and marking of non-domestic gas-fired overhead radiant tube heaters incorporated into a multi-burner system with each burner unit under the control of an automatic burner control system. Applicable to Type B[22] and Type B[23] systems intended for use in other than domestic dwelling, in which the supply of combustion air and/or evacuation of the products of combustion is achieved by mechanical means. Applicable to systems which are intended to be type tested.

DevelopmentNote	Indice de classement: E31-404-2. (04/2002) PR NF EN 777-2 November 2006. (11/2006)
DocumentType	Standard
PublisherName	Association Francaise de Normalisation
Status	Superseded
SupersededBy	NF EN 416:2019

Standards	Relationship
BS EN 777-2:2009	Identical
I.S. EN 777-2:2009	Identical
UNI EN 777-2 : 2009	Identical
NS EN 777-2 : 2009	Identical
SN EN 777-2 : 2009	Identical
UNE-EN 777-2:2009	Identical
DIN EN 777-2:2009-09	Identical
NBN EN 777-2 : 2009	Identical
EN 777-2:2009	Identical
NEN EN 777-2 : 2009	Identical

NF EN 60335-2-102 : 2016	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-102: PARTICULAR REQUIREMENTS FOR GAS, OIL AND SOLID-FUEL BURNING APPLIANCES HAVING ELECTRICAL CONNECTIONS
NF EN ISO 228-1 : 2003	PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
NF ISO 619976 : 1997	NATURAL GAS - CALCULATION OF CALORIFIC VALUES, DENSITY, RELATIVE DENSITY WOBBE INDEX FROM COMPOSITION
ISO 7005-2:1988	Metallic flanges — Part 2: Cast iron flanges
NF EN 88-1 : 2011 + A1 2016	PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
NF EN 437 : 2003 + A1 2009	TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES
89/106/EEC : 1988	COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
ISO 7005-3:1988	Metallic flanges Part 3: Copper alloy and composite flanges
NF EN 126 : 2012	MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
NF EN 60529 : 92 AMD 2 2014	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
NF EN 60335-1 : 2013	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS
CR 1404:1994	Determination of emissions from appliances burning gaseous fuels during type-testing
NF EN 257 : 2011	MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES
NF EN ISO 3166-1 : 2014	CODES FOR THE REPRESENTATION OF NAMES OF COUNTRIES AND THEIR SUBDIVISION - PART 1: COUNTRY CODES
NF EN 60584-2 : 1993	THERMOCOUPLES - PART 2: TOLERANCES
NF EN 10226-1 : 2004	PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 1: TAPER EXTERNAL THREADS AND PARALLEL INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION
ISO 7005-1:2011	Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
NF EN 161 : 2011 + A3 2013	AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
NF EN 298 : 2012	AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
NF EN 10226-2 : 2005	PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 2: TAPER EXTERNAL THREADS AND TAPER INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION
NF EN 60584-1 : 2014	THERMOCOUPLES - PART 1: EMF SPECIFICATIONS AND TOLERANCES
1990/396/EEC : 1990	COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS