Name: ONORM EN 1218-1 : 2010
Brand: ON

ONORM EN 1218-1 : 2010

Superseded

View Superseded by

SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE

Superseded date

10-21-2021

Published date

01-12-2013

Publisher

Osterreichisches Normungsinstitut/Austrian Standards

Foreword
      Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
5 Safety requirements and/or measures
      5.1 Controls
      5.2 Protection against mechanical hazards
      5.3 Protection against non-mechanical hazards
6 Information for use
      6.1 Warning devices
      6.2 Marking
      6.3 Instruction handbook
Annex A (informative) Safe working practice
Annex B (normative) Geometrical performance for the
                    tool holder (spindle) (taken from
                    ISO 7988:1988)
Annex C (informative) Examples of safety related control
                      systems
Annex D (informative) Bibliography
Annex ZA (informative) Clauses of this European Standard
                       addressing essential requirements
                       or other provisions of EU
                       Directives

Defined requirements and/or measures to remove the hazards and limit the risk on single end tenoning machines with sliding table, referred to as "machine". These are designed to cut solid wood, fibreboard, chipboard, plywood and materials where they are covered with plastic edgings or laminates.

Committee	TC-028
DocumentType	Standard
PublisherName	Osterreichisches Normungsinstitut/Austrian Standards
Status	Superseded
SupersededBy	ÖNORM EN ISO 19085-12:2021 10 15

Standards	Relationship
NEN EN 1218-1 : 1999 + A1 2009	Identical
UNE-EN 1218-1:2000	Identical
SN EN 1218-1 : 1999 + A1 2010	Identical
EN 1218-1:1999+A1:2009	Identical
I.S. EN 1218-1:2000	Identical
NS EN 1218-1 : 1999 + A1 2009	Identical
BS EN 1218-1 : 1999	Identical
UNI EN 1218-1 : 2009	Identical
NBN EN 1218-1 : 1999 + A1 2009	Identical
DIN EN 1218-1:2010-02	Identical
NF EN 1218-1 : 2000 + A1 2009	Identical

ONORM EN ISO 3743-2 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
ISO 11202:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
ISO 4871:1996	Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 3744:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ISO/TR 11688-1:1995	Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 3743-2:1994	Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms
ONORM EN ISO 13857 : 2008	SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS
ISO 9614-1:1993	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
ONORM EN ISO 11204 : AUG 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS
ISO 3746:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
ISO 12100-2:2003	Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 13857:2008	Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
ISO 12100-1:2003	Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 13850:2015	Safety of machinery Emergency stop function Principles for design
ISO 3745:2012	Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
ISO 11204:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
ONORM EN ISO 11202 : 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
ISO 3743-1:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room