Name: ONORM EN ISO 13000-2 : 2006
Brand: ON

ONORM EN ISO 13000-2 : 2006

Withdrawn

PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

Withdrawn date

11-15-2021

Published date

01-12-2013

Publisher

Osterreichisches Normungsinstitut/Austrian Standards

1 Scope
2 Normative references
3 Definitions
4 Sampling
5 Preparation of test specimens
6 Testing of semi-finished PTFE products
    6.1 General
    6.2 Linear dimensions
    6.3 Tensile properties
    6.4 Density
    6.5 Loss of mass at 300 deg c
    6.6 Dimensional stability - general method
    6.7 Dimensional stability - Special method for
          determination of dimensional and geometric
          stabilities of thick-walled tube
    6.8 Electrical properties
    6.9 Hardness
    6.10 Colour
    6.11 Radiographic examination
    6.12 Resistance to environmental stress cracking (ESC)
    6.13 Deformation under load
Annex A (informative) Other standards relating to testing
semi-finished products of PTFE

Describes the preparation of test specimens and gives the test methods applicable to semi-finished products of polytetrafluoroethylene (PTFE).

Committee	TC 074
DocumentType	Standard
PublisherName	Osterreichisches Normungsinstitut/Austrian Standards
Status	Withdrawn
SupersededBy	ÖNORM EN ISO 13000-2:2021

Standards	Relationship
ISO 13000-2:2005	Identical
UNE-EN ISO 13000-2:2006	Identical
I.S. EN ISO 13000-2:2006	Identical
EN ISO 13000-2:2005	Identical
BS EN ISO 13000-2:2005	Identical
NS EN ISO 13000-2 : 2ED 2006	Identical
NEN EN ISO 13000-2 : 2005	Identical
UNI EN ISO 13000-2 : 2006	Identical
NBN EN ISO 13000-2 : 2006	Identical
NF EN ISO 13000-2 : 2006	Identical
SN EN ISO 13000-2 : 2006	Identical
DIN EN ISO 13000-2:2006-02	Identical

IEC 60243-1:2013	Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
ISO 1923:1981	Cellular plastics and rubbers — Determination of linear dimensions
ISO 2039-1:2001	Plastics Determination of hardness Part 1: Ball indentation method
ISO 527-2:2012	Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 472:2013	Plastics Vocabulary
ISO 13000-1:2005	Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation
ISO 1183-1:2012	Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 3611:2010	Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
ISO 4599:1986	Plastics Determination of resistance to environmental stress cracking (ESC) Bent strip method
IEC 60243-2:2013	Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage
ISO 527-3:1995	Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
ISO 4600:1992	Plastics Determination of environmental stress cracking (ESC) Ball or pin impression method
ISO 868:2003	Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)