• There are no items in your cart

PREN 12779 : DRAFT 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY OF WOODWORKING MACHINES - CHIPS AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATIONS - SAFETY REQUIREMENTS
Superseded date

11-01-2015

Published date

02-05-2014

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, terminology and symbols
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (informative) - Examples of extraction
        systems
Annex B (informative) - Table with corresponding terms
        in English, French and German
Annex C (informative) - Classification of places where
        explosive atmospheres may occur (according
        to Directive 1999/92/EC)
Annex D (informative) - Noise reduction at the design
        stage
Annex E (normative) - Silos with a cross section up to
        45 m[2]
Annex F (informative) - Measurement of residual dust
        content
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC
Bibliography

Describes the significant hazards, hazardous situations and events relevant for chip and dust extraction systems (woodworking) with fixed installation, when they are used as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse.

Committee
TC 142
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
14/30292850 DC : 0 Identical

04/30106849 DC : DRAFT MAY 2004 EN 1870-1 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 1: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE), DIMENSION SAWS AND BUILDING SITE SAWS
04/30110326 DC : DRAFT APR 2004 EN 1870-17 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT CIRCULAR SAWING MACHINES WITH ONE SAW UNIT (MANUAL RADIAL ARM SAWS)
04/301784 DC : DRAFT JAN 2004 EN 848-2 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HANDFED/INTEGRATED FED ROUNTING MACHINES
02/705139 DC : DRAFT APR 2002 PREN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING

EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
EN 1870-4:2012 Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 848-3:2012 Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines
EN 15089:2009 Explosion isolation systems
EN 16009:2011 Flameless explosion venting devices
ISO 14122-3:2016 Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
EN 617:2001+A1:2010 Continuous handling equipment and systems - Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
EN 14373:2005 Explosion suppression systems
EN 12792:2003 Ventilation for buildings - Symbols, terminology and graphical symbols
EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 14797:2006 Explosion venting devices
EN 60079-10-2:2015 Explosive atmospheres - Part 10-2: Classification of areas - Explosive dust atmospheres
2004/108/EC : 2004 DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 DECEMBER 2004 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO ELECTROMAGNETIC COMPATIBILITY AND REPEALING DIRECTIVE 89/336/EC
EN 14491:2012 Dust explosion venting protective systems
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
EN 1366-1:2014 Fire resistance tests for service installations - Part 1: Ventilation ducts
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 14122-4:2016 Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
EN 14986:2017 Design of fans working in potentially explosive atmospheres
EN 62305-4:2011/AC:2016-11 Protection against lightning - Part 4: Electrical and electronic systems within structures
IEC 62305-1:2010 Protection against lightning - Part 1: General principles
ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
EN 1366-7:2004 Fire resistance tests for service installations - Part 7: Conveyor systems and their closures
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 1093-7:1998+A1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Separation efficiency by mass, ducted outlet
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN ISO 4414:2010 Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010)
EN ISO 14122-4:2016 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
EN ISO 14122-2:2016 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
IEC 60079-14:2013 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 1366-2:2015 Fire resistance tests for service installations - Part 2: Fire dampers
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 13779:2007 Ventilation for non-residential buildings - Performance requirements for ventilation and room-conditioning systems
ISO 14122-2:2016 Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
1994/9/EC : 1994 DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 12750:2013 Safety of woodworking machines - Four sided moulding machines

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.