• There are no items in your cart

PREN 1493 : DRAFT 2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

VEHICLE LIFTS
Superseded date

12-01-2008

Published date

01-12-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
   5.1 Preventing unauthorised operation
   5.2 Control devices
   5.3 Control positions
   5.4 Duplicated drive systems
   5.5 Speeds
   5.6 Structural design of the supporting structure
   5.7 Driving machinery
   5.8 Load carrying devices
   5.9 Additional requirements for lifts with balconies
   5.10 Limiting the travel of the load carrying device
   5.11 Unintended blocking of the load carrying device
   5.12 Safety against rupture of mechanical bearing devices
   5.13 Safety against leakage
   5.14 Additional requirements for lifts with several drives
        or lifting elements
   5.15 Additional requirements for movable and mobile lifts
   5.16 Protection against pinching and shearing
   5.17 Safety devices
   5.18 Protection against damage
   5.19 Manually driven vehicle lifts
   5.20 Electrical equipment
6 Verification of the safety requirements and/or measures
   6.1 General
7 Information for use
   7.1 General
   7.2 Marking
   7.3 Operation instructions
   7.4 Name plate
Annex A (informative) - Structural calculations
   A.1 Permissible stresses
Annex B (informative) - Examples of solutions
Annex C (normative) - Design of rope drives
Annex D (informative) - Example of information about wind
Annex E (normative) - Protection against leakage
Annex F (normative) - Additional requirements for cableless
        controls and control systems
   F.1 General
   F.2 Control limitation
   F.3 Stop
   F.4 Serial data communication
   F.5 Use of more than one operator control station
   F.6 Battery-powered operator control stations
   F.7 Receiver
   F.8 Warnings
   F.9 Information for use
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU Directive
         98/37/EC
Annex ZB (informative) - Relationship between this European
         Standard and the Essential Requirements of EU Directive
         2006/42/EC

Applies to stationary, mobile and movable vehicle lifts, which are not intended to lift persons but which are designed to raise vehicles totally, for the purpose of examining and working on or under the vehicles whilst in a raised position.

Committee
TC 98
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
08/30187719 DC : 0 Identical

CEN Guide 414:2017 Safety of machinery - Rules for the drafting and presentation of safety standards
ISO 4308-1:2003 Cranes and lifting appliances Selection of wire ropes Part 1: General
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
IEC 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
EN ISO 13849-2:2012 Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN 1760-2:2001+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.