SAE AMS 4049 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 5.6ZN - 2.5MG - 1.6CU - 0.23CR (ALCLAD 7075; -T6 SHEET - T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED
Available format(s)
Hardcopy , PDF
Superseded date
08-20-2022
Language(s)
English
Published date
06-16-2016
Publisher
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
Specifies an aluminum alloy in the form of sheet and plate with thickness from 0.008 to 4.000 inch, incl (0.20 to 101.6 mm, incl), clad on two sides.
| Committee |
AMS-D
|
| DevelopmentNote |
Supersedes SAE AMS 4039 (07/1999) Supersedes SAE AMS QQ A 250/13. (07/2011)
|
| DocumentType |
Revision
|
| Pages |
6
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE AMS 1450 : 1998 | DISINFECTANT (INSECTICIDE), AIRCRAFT |
| SAE AMS 1426 : 2016 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS GLYCOL BASE |
| SAE AMS 1548 : 2017 | CLEANER, TURBINE ENGINE GAS PATH, SOLVENT EMULSION TYPE |
| SAE AMS 1640 : 2011 | CORROSION REMOVING COMPOUND, FOR AIRCRAFT SURFACES |
| SAE AMS 1428 : 2017 | FLUID, AIRCRAFT DEICING/ANTI-ICING, NON-NEWTONIAN, (PSEUDOPLASTIC), SAE TYPES 2, 3 AND 4 |
| MIL-S-83318 Revision A:1991 | SEALING COMPOUND, LOW TEMPERATURE CURING, QUICK REPAIR, INTEGRAL FUEL TANKS AND FUEL CELL CAVITIES |
| SAE AMS 3263 : 1997 | SEALING COMPOUND, POLYTHIOETHER, AMBIENT CURE OR IMMEDIATE HEAT CURE FOR AIRCRAFT STRUCTURES, FUEL RESISTANT WITH INTERMITTENT USE TO 400 MDCF (204 MDCC) |
| SAE AMS 3265 : 2015 | SEALING COMPOUND, POLYSULFIDE (T) RUBBER, FUEL RESISTANT, NON-CHROMATED CORROSION INHIBITING, FOR INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C) |
| SAE AS 5127 : 2013 | AEROSPACE STANDARD TEST METHODS FOR AEROSPACE SEALANTS METHODS FOR PREPARING AEROSPACE SEALANT TEST SPECIMENS |
| SAE AMS 1535C : 2008 | CLEANER, TRANSPARENT PLASTIC |
| SAE AMS 1540 : 2015 | CLEANER, THRUST REVERSER, WATER-BASE |
| SAE AMS 1550 : 2012 | CLEANER, WATER BASE, AIRCRAFT INTERIOR HARD SURFACE MATERIALS |
| SAE AMS 1476 : 2016 | DEODORANT, AIRCRAFT TOILET |
| SAE AMS 1526 : 2008 | CLEANER FOR AIRCRAFT EXTERIOR SURFACES, WATER-MISCIBLE, PRESSURE-SPRAYING TYPE |
| SAE AS 81550A : 2014 | INSULATING COMPOUND, ELECTRICAL, EMBEDDING, REVERSION RESISTANT SILICONE |
| SAE AMS 1453 : 2015 | DISINFECTANT CLEANER FOR AIRCRAFT INTERIOR GENERAL PURPOSE LIQUID |
| SAE AMS 1375 : 2012 | REMOVER, PAINT, EPOXY AND POLYURETHANE PAINT SYSTEMS |
| BS M 75:1994 | Aircraft de-icing/anti-icing Newtonian fluids, ISO type I |
| SAE AMS 3809 : 2015 | TAPE, ADHESIVE, PRESSURE-SENSITIVE, DOUBLE-FACED, CARPET TIE DOWN |
| SAE AMS 1320 : 1995 | REMOVER, DECAL ADHESIVE |
| SAE AMS 1377 : 2012 | REMOVER, PAINT, EPOXY AND POLYURETHANE PAINT SYSTEM, NON-CHLORINATED SOLVENT |
| SAE AMS 1630 : 2008 | CLEANER, CARPET SHAMPOO TYPE |
| SAE AMS 1376 : 1998 | REMOVER, EPOXY PAINT, ACID TYPE, THICKENED |
| SAE AMS 1424 : 2017 | FLUID, AIRCRAFT DEICING/ANTI-ICING, SAE TYPE 1 |
| SAE AMS 1725 : 1986 | SKIN PROTECTIVE COMPOUND, CHEMICAL BARRIER |
| SAE AMS 3377 : 2015 | SEALING COMPOUND, ELECTRICALLY CONDUCTIVE CORROSION INHIBITING |
| SAE AMS S 4383 : 2015 | SEALING COMPOUND, TOPCOAT, FUEL TANK BUNA-N TYPE |
| BS M 78:1995 | Aircraft de-icing/anti-icing non-Newtonian fluids, ISO type II |
| SAE AMS 3077 A : 1994(S2018) | COMPOUND, CORROSION PREVENTIVE, SOFT FILM, THIXOTROPIC, COLD APPLICATION |
| SAE AMS 3259 : 1997 | SEALING COMPOUND, POLYTHIOETHER - NONCHROMATED, CORROSION INHIBITING FOR INTERMITTENT USE TO 360 DEGREE F (182 DEGREE C) |
| SAE AMS 1374 : 2004 | REMOVER, POLYURETHANE/EPOXY PAINT, ALKALINE, HOT-TANK TYPE |
| SAE AS 5127/1 : 2014 | AEROSPACE STANDARD TEST METHODS FOR AEROSPACE SEALANTS TWO-COMPONENT SYNTHETIC RUBBER COMPOUNDS |
| SAE AMS 1551 : 2008 | CLEANER, TURBINE ENGINE GAS PATH AQUEOUS TYPE |
| SAE AMS 1536 : 2008 | CLEANER FOR AIRCRAFT COMPONENTS COLD TANK TYPE, SOLVENT-BASE |
| SAE AMS 3267 : 1992 | SEALING COMPOUND, LOW ADHESION, CORROSION INHIBITING, FOR REMOVABLE PANELS AND FUEL TANK INSPECTION PLATES |
| SAE AMS 1431 : 2012 | COMPOUND, SOLID RUNWAY AND TAXIWAY DEICING/ANTI-ICING |
| SAE AMS 1432 : 1995 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS, POTASSIUM ACETATE BASE |
| SAE AMS 1452 : 2015 | DISINFECTANT, AIRCRAFT, GENERAL PURPOSE |
| SAE AMS 1534 : 2013 | CLEANER, AIRCRAFT GLASS WINDOW |
| SAE AMS 1659 : 1991 | COATING, SOIL BARRIER, SEMI-PERMANENT |
| SAE AMS 1435 : 2012 | FLUID, GENERIC, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS |
| MIL-PRF-32587 Base Document:2018 | Remover, Paint, Hap-Free, Neutral |
| SAE AMS 1527 : 2014 | CLEANER FOR AIRCRAFT EXTERIOR SURFACES, WATER-MISCIBLE, FOAM-ON, PRESSURE-SPRAYING |
| SAE AMS 1388 : 2008 | REMOVER, TEMPORARY COATING, ALKALINE TYPE, WATER BASE |
| SAE AMS 3284 : 2017 | SEALING COMPOUND, LOW ADHESION, FOR REMOVABLE PANELS AND FUEL TANK INSPECTION PLATES |
| SAE AMS 1451 : 1998 | DISINFECTANT, AIRCRAFT FOR USE IN CARGO COMPARTMENTS |
| SAE AMS 1631 : 2005 | CLEANER, CARPET WATER EXTRACTION TYPE |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| ANSI H35.1/H35.1M : 2017 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM |
| ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
| SAE ARP 1917 : 2002 | CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS |
| SAE AMS 2772 : 2016 | HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS |
| SAE AMS 2355 : 2016 | QUALITY ASSURANCE, SAMPLING AND TESTING, ALUMINUM ALLOYS AND MAGNESIUM ALLOY, WROUGHT PRODUCTS (EXCEPT FORGING STOCK), AND ROLLED, FORGED, OR FLASH WELDED RINGS |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
US$81.42
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.