• SAE AMS 4921 : 2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    TITANIUM BARS, WIRE, FORGINGS, AND RINGS COMMERCIALLY PURE, 70 KSI (483 MPA) YIELD STRENGTH

    Available format(s):  Hardcopy, PDF

    Superseded date:  04-07-2020

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 SCOPE
    2 APPLICABLE DOCUMENTS
    3 TECHNICAL REQUIREMENTS
    4 QUALITY ASSURANCE PROVISIONS
    5 PREPARATION FOR DELIVERY
    6 ACKNOWLEDGMENT
    7 REJECTIONS
    8 NOTES

    Abstract - (Show below) - (Hide below)

    Specifies one grade of commercially-pure titanium in the form of bars, wire, forgings, flash welded rings, up to 4.000 inches (101.60 mm), inclusive, in nominal diameter or least distance between parallel sides, and stock for forging or flash welded rings.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-G
    Development Note Supersedes SAE AMS T 9047. (08/2006)
    Document Type Revision
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    MIL F 85720 : 0 FITTING, TUBE, FLUID SYSTEMS, SEPARABLE, HIGH PRESSURE, DYNAMIC BEAM, SEAL, GENERAL SPECIFICATION FOR
    SAE AS 5356 : 2017 COUPLING, FUEL LINE, FLEXIBLE, 125 PSI GENERAL SPECIFICATION FOR
    MIL STD 1587 : D MATERIAL AND PROCESS REQUIREMENTS FOR AEROSPACE WEAPONS SYSTEMS
    SAE AS 4459 : 2013 FITTINGS, TUBE, FLUID SYSTEM 3000 PSIG (21000 KPA) RATED PRESSURE, EXTERNALLY SWAGED, SPECIFICATION FOR
    SAE AS 269J:2012:(S2018) IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS
    SAE AS 1975 : 2016 HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PARA-ARAMID REINFORCED, 3000/4000 PSI, 275 DEGREES F, STANDARD DUTY, HYDRAULIC, AIRCRAFT SYSTEMS
    SAE AS 85421 : 2015 FITTINGS, TUBE, FLUID SYSTEMS, SEPARABLE, BEAM SEAL, 3000/4000 PSI, GENERAL SPECIFICATION FOR
    SAE AIR 5693 : 2014 COMPATIBILITY OF PTFE HOSE ASSEMBLIES WITH TYPICAL FLUIDS FOUND IN AEROSPACE APPLICATIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AMS 2241 : 2016 TOLERANCES, CORROSION AND HEAT-RESISTANT STEEL, IRON ALLOY, TITANIUM, AND TITANIUM ALLOY BARS AND WIRE
    ASTM E 2371 : 2013 Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)
    SAE AMS 2368 : 2017 SAMPLING AND TESTING OF WROUGHT TITANIUM RAW MATERIAL EXCEPT FORGINGS AND FORGING STOCK
    SAE AMS 2809 : 2007(R2011) IDENTIFICATION, TITANIUM AND TITANIUM ALLOY WROUGHT PRODUCTS
    SAE AMS 2750 : 2012 PYROMETRY
    ASTM E 1409 : 2013 : REDLINE Standard Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion
    SAE AMS 2631 : 2011 ULTRASONIC INSPECTION, TITANIUM AND TITANIUM ALLOY BAR, BILLET AND PLATE
    SAE ARP 1917 : 2002 CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS
    SAE AMS 7498 : 2016 RINGS, FLASH WELDED TITANIUM AND TITANIUM ALLOYS
    SAE AS 6279 : 2016 STANDARD PRACTICE FOR PRODUCTION, DISTRIBUTION, AND PROCUREMENT OF METAL STOCK
    SAE AMS 2249 : 2013 CHEMICAL CHECK ANALYSIS LIMITS, TITANIUM AND TITANIUM ALLOYS
    SAE AMS 2808 : 2017 IDENTIFICATION FORGINGS
    ASTM E 8/E8M : 2016-09 TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective