SAE AMS DTL 23053 : 1999

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Add to Watchlist

View superseded by

This Standard has been added successfully to your Watchlist.
Please visit My Watchlist to see all standards that you are watching.

Please log in or create an account to add this standard to your Watchlist.

We could not add this standard to your Watchlist.
Please retry or contact support for assistance.

You have already added this standard to your Watchlist.
Visit My Watchlist to view the full list.

INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR

Available format(s):

Superseded date: 10-16-2016

Language(s):

Published date: 01-01-1999

Publisher: SAE International

Add to Watchlist

Table of Contents - (Show below) - (Hide below)

1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES

Abstract - (Show below) - (Hide below)

Determines the requirements for various kinds and colors of electrical insulating sleeving which will shrink to a predetermined size upon applying heat.Includes provisions for demonstration of compliance with requirements through in process inspection and statistical process control. Continuous operating temperatures are in the range -80 deg to +250 deg C (-112 deg to + 482 deg F).

General Product Information - (Show below) - (Hide below)

Committee	FSC 5970
Development Note	Supersedes MIL DTL 23053 (08/1999)
Document Type	Standard
ISBN
Pages
Published
Publisher	SAE International
Status	Superseded
Superseded By	SAE AS 23053 : 2016 SAE AMS DTL 23053 A : 2018

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
MIL DTL 23053 : E	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

SAE AS 95234 : 2014	CONNECTORS, ELECTRICAL, REVERSE BAYONET, GENERAL SPECIFICATION FOR
MIL PRF 32517 : 0	SPLICE, CONDUCTOR, ELECTRICAL, COAXIAL CABLE, MATCHED IMPEDANCE, GENERAL SPECIFICATION FOR
SAE AS 95234A : 2020	CONNECTORS, ELECTRICAL, REVERSE BAYONET, GENERAL SPECIFICATION FOR
SAE ARP 4945 : 2013	AEROSPACE-SOLENOID VALVE, HYDRAULIC, THREE WAY, TWO POSITION, DIRECT ACTING
I.S. EN 6049-009:2016	AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTION SLEEVE IN META-ARAMID FIBRES - PART 009: SELF-WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE, POST INSTALLATION, OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
BS EN 6049-009:2016	AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTION SLEEVE IN META-ARAMID FIBRES - PART 009: SELF-WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE, POST INSTALLATION, OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
MIL DTL 2726/49 : F	RECEPTACLE, OUTLET, TRIPLE, ELECTRICAL, 40 - AMPERE, 450 - VOLT, 60 HERTZ, ALTERNATING CURRENT, 4 - POLE, PORTABLE, PLASTIC GROUNDED (SYMBOL NOS. 765.6, 765.7 AND 765.8)
PD ISO/TR 21891:2017	Aerospace electrical requirements. Sleeves and moulded shapes. Specifications for aircraft use
MIL DTL 15024/8 : A	PLATE, TAGS AND BANDS, BAND IDENTIFICATION, CABLE ASSEMBLY, TYPE K2, HEAT SHRINKABLE TUBING
NASA KSC E 165 : 2009	ELECTRICAL GROUND SUPPORT EQUIPMENT FABRICATION, SPECIFICATION FOR
NASA KSC GP 864 VOL 2A : 2009	ELECTRICAL GROUND SUPPORT EQUIPMENT CABLE HANDBOOK
NASA KSC STD 132 : 2008	POTTING AND MOLDING ELECTRICAL CABLE ASSEMBLY TERMINATIONS, STANDARD FOR
MIL HDBK 522 : A	GUIDELINES FOR INSPECTION OF AIRCRAFT ELECTRICAL WIRING INTERCONNECT SYSTEMS
MIL STD 2042/5 : C	FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS AND INTERCONNECTIONS) (PART 5 OF 7 PARTS)
EN 6049-009 : 2016	Aerospace series - Electrical cables, installation - Protection sleeve in meta-aramid fibres - Part 009: Self-wrapping fire protection sleeve, flexible, post installation, operating temperature from -55 °C to 260 °C - Product standard
PREN 6049-009 : 200P3	AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTION SLEEVE IN META-ARAMID FIBRES - PART 009: SELF-WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE POST INSTALLATION OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
12/30275061 DC : 0	BS EN 6049-009 - AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTIVE SLEEVE IN ARAMID FIBRES - PART 009: SELF WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE POST INSTALLATION OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
SAE AS 50881 : 2015	WIRING AEROSPACE VEHICLE
MIL PRF 39006 : G	CAPACITOR, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
SAE AS 5258 : 2012	INSULATING COMPONENT, MOLDED, ELECTRICAL, HEAT SHRINKABLE, CONNECTOR AND CABLE ACCESSORY, SEALING STRAIN RELIEF, GENERAL SPECIFICATION FOR
SAE AS 6224 : 2015	WRAP-AROUND INSULATION REPAIR AND PROTECTION SLEEVE, PERMANENT, ELECTRIC, ENVIRONMENT RESISTANT

Standards Referencing This Book - (Show below) - (Hide below)

MIL DTL 23053/8 : C	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, SEMI-RIGID, CROSSLINKED
MIL L 7808 : K (1)	LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE
FED STD 228 : A	TEST METHODS FOR CABLES AND WIRE, INSULATED
MIL I 23053/3 : A	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYVINYL CHLORIDE, SEMI RIGID, CROSSLINKED AND NON CROSSLINKED
MIL DTL 23053/14 : B	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, ETHYLENE-TETRAFLUOROETHYLENE FLUOROPOLYMER, SEMI-RIGID
MIL DTL 23053/17 : B	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLAME RETARDED, MODIFIED POLYOLEFIN, FLEXIBLE, CROSSLINKED
MIL DTL 23053/10 : D	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, SILICONE RUBBER, FLEXIBLE
MIL DTL 23053/18 : B	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, MODIFIED FLUOROPOLYMER, CROSSLINKED
MIL DTL 23053/7 : C	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYETHYLENE TEREPHTHALATE, NON-CROSSLINKED
ASTM G 21 : 2015 : REDLINE	Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
MIL L 23699 : E	LUBRICATING OIL, AIRCRAFT TURBINE ENGINES, SYNTHETIC BASE
A A 694 : E	SODIUM CHLORIDE, TECHNICAL
MIL DTL 23053/13 : B	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUOROELASTOMER FLEXIBLE
MIL T 5624 : R	TURBINE FUEL, AVIATION, GRADES JP 4 AND JP 5
MIL DTL 23053/15 : B	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, HEAVY-WALL, COATED, FLEXIBLE, OUTER WALL CROSSLINKED
ASTM D 792 : 2013 : REDLINE	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
MIL I 23053/2 : C	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYVINYL CHLORIDE, FLEXIBLE, CROSSLINKED AND NON CROSSLINKED
MIL I 23053/9 : LATEST	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUOROSILICONE RUBBER, FLEXIBLE
MIL DTL 23053/16 : B	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED, ELASTOMERIC POLYOLEFIN, FLEXIBLE
MIL DTL 23053/5 : C	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE, CROSSLINKED
MIL DTL 23053/11 : C	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUORINATED ETHYLENE PROPYLENE, NON-CROSSLINKED
ASTM D 876 : 2013 : REDLINE	Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
MIL A 8243 : D	ANTI-ICING AND DEICING-DEFROSTING FLUIDS
MIL DTL 23053/12 : C	INSULATION SLEEVING - ELECTRICAL, HEAT SHRINKABLE, POLYTETRAFLUOROETHYLENE
MIL DTL 23053/1 : C	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE
MIL H 5606 : G	HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE
MIL F 46162 : D	FUEL, DIESEL, REFEREE GRADE
ASTM D 570 : 1998 : R2018	Standard Test Method for Water Absorption of Plastics
MIL DTL 23053/6 : D	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, SEMI-RIGID, CROSSLINKED
MIL STD 104 : C	LIMITS FOR ELECTRICAL INSULATION COLOR
ASTM D 638 : 2014 : REDLINE	Standard Test Method for Tensile Properties of Plastics
MIL DTL 23053/4 : D	INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, DUAL-WALL, OUTER WALL CROSSLINKED
ASTM D 2671 : 2013	Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use
ASTM D 374 : 1999	Standard Test Methods for Thickness of Solid Electrical Insulation
ASTM D 746 : 2014 : REDLINE	Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart