• SAE AMS QQ A 250 B : 2012

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    ALUMINUM AND ALUMINUM ALLOY, PLATE AND SHEET GENERAL SPECIFICATION FOR

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-03-2016

    Language(s): 

    Published date:  01-01-2012

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 SCOPE AND CLASSIFICATION
    2 APPLICABLE DOCUMENTS
    3 REQUIREMENTS
    4 QUALITY ASSURANCE PROVISIONS
    5 PREPARATION FOR DELIVERY
    6 NOTES

    Abstract - (Show below) - (Hide below)

    General requirements that are for aluminum and aluminum alloy plate and sheet are covered in this specification.

    General Product Information - (Show below) - (Hide below)

    Committee AMS D
    Development Note Supersedes QQ A 250. (07/2000)
    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    MIL DTL 15370 : K COUPLERS, DIRECTIONAL, GENERAL SPECIFICATION FOR
    MIL DTL 3928 : H SWITCHES, RADIO-FREQUENCY TRANSMISSION LINE, (COAXIAL AND MICROSTRIP), GENERAL SPECIFICATION FOR
    MIL DTL 23971 : E POWER DIVIDERS, POWER COMBINERS, AND POWER DIVIDER/COMBINERS, GENERAL SPECIFICATION FOR
    MIL PRF 32287 : A PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT
    MIL PRF 87260 : B FOAM MATERIAL, EXPLOSION SUPPRESSION, INHERENTLY ELECTROSTATICALLY CONDUCTIVE, FOR AIRCRAFT FUEL TANKS
    MIL PRF 680 : C DEGREASING SOLVENT
    MIL DTL 28754/17 : E CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR ASSEMBLY, TYPE 5, STYLE 1, CONTACT TAILS ON .100 CENTERS
    MIL-DTL-28837D : 2015 MIXER STAGES, RADIO FREQUENCY GENERAL SPECIFICATION FOR
    MIL DTL 24251/6 : E SHIELD, ELECTRON TUBE, HEAT DISSIPATING, 7 AND 9 PIN, MINIATURE (RETROFIT TYPE ONLY)
    MIL DTL 24251/5 : D SHIELD, ELECTRON TUBE, HEAT DISSIPATING, 7 AND 9 PIN, MINIATURE (OPEN SIDES)
    MIL DTL 25708/1 : H ANTENNA, BLADE, AT-741B/B (HN CONNECTOR)
    MIL DTL 24251/3 : D SHIELD, ELECTRON TUBE, HEAT DISSIPATING 7 AND 9 PIN, MINIATURE (SPLIT SHELL)
    MIL DTL 38449 : D SIGNAL AND SIGNAL/INTERCOMMUNICATION AMPLIFIERS, UNIVERSAL, AERIAL REFUELING
    MIL DTL 28875 : C AMPLIFIERS, RADIO-FREQUENCY AND MICROWAVE, SOLID-STATE, GENERAL SPECIFICATION FOR
    MIL PRF 0032287 : 0 PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT
    MIL DTL 28754/7 : D CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, SINGLE SPAN, CONNECTOR ASSEMBLY
    MIL PRF 87937 : D CLEANING COMPOUND, AEROSPACE EQUIPMENT
    MIL STD 2042/1 : C FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CABLES) (PART 1 OF 7 PARTS)
    SAE AMS 8660 : 2018 SILICONE COMPOUND NATO CODE NUMBER S-736
    SAE AS 81659 : 2017 CONNECTORS, ELECTRICAL, RECTANGULAR CRIMP CONTACTS, GENERAL SPECIFICATION FOR
    IPC 2221B:2012 GENERIC STANDARD ON PRINTED BOARD DESIGN
    IPC 2221 FRENCH : B2012 GENERIC STANDARD ON PRINTED BOARD DESIGN

    Standards Referencing This Book - (Show below) - (Hide below)

    ANSI H35.2 : 2017 DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS
    ASTM B 557 : 2015 : REDLINE Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
    FED STD 123 : H MARKING FOR SHIPMENT (CIVIL AGENCIES)
    SAE AMS 2772 : 2016 HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS
    SAE AMS STD 184 : 2000 IDENTIFICATION MARKING OF ALUMINUM, MAGNESIUM, AND TITANIUM
    ANSI H35.1 : 2006 ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM
    ASTM E 290 : 2014 : REDLINE Standard Test Methods for Bend Testing of Material for Ductility
    ASTM E 1004 : 2017 : REDLINE Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method
    ASTM B 660 : 2015 : REDLINE Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective