Name: SAE AS 5127 : 2013
Brand: SAE

SAE AS 5127 : 2013

Superseded

View Superseded by

AEROSPACE STANDARD TEST METHODS FOR AEROSPACE SEALANTS METHODS FOR PREPARING AEROSPACE SEALANT TEST SPECIMENS

Superseded date

11-17-2018

Published date

01-01-2013

Publisher

SAE International

1. SCOPE
2. APPLICABLE DOCUMENTS
3. STANDARD TOLERANCES
4. STANDARD CONDITIONS
5. STANDARD HEAT CYCLES
6. PREPARATION OF TEST SPECIMENS
7. STANDARD TEST FLUIDS
8. TEST METHODS
9. NOTES

Describes the accepted methods used for preparing aerospace sealant test specimens for qualification and quality conformance or acceptance testing.

Committee	AMS G9
DocumentType	Standard
PublisherName	SAE International
Status	Superseded
SupersededBy	SAE AS 5127C : 2018
Supersedes	SAE AS 5127 : 2002

SAE AS 5127/2 : 2014	TEST METHOD FOR AEROSPACE FIREWALL SEALANT FLAME PENETRATION
SAE AMS 3281 : 2016	SEALING COMPOUND, POLYSULFIDE (T) SYNTHETIC RUBBER FOR INTEGRAL FUEL TANK AND FUEL CELL CAVITIES LOW DENSITY FOR INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
SAE AMS 3265 : 2015	SEALING COMPOUND, POLYSULFIDE (T) RUBBER, FUEL RESISTANT, NON-CHROMATED CORROSION INHIBITING, FOR INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
SAE AMS 3278 : 2016	SEALING AND COATING COMPOUND, POLYURETHANE (PUR), FUEL RESISTANT, HIGH TENSILE STRENGTH/ELONGATION, FOR INTEGRAL FUEL TANKS/FUEL CAVITIES/GENERAL PURPOSE
SAE AMS 3379 : 2013(R2018)	SEALING COMPOUND, POLYSULFIDE RUBBER PREFORMED STRIPS FOR SEALING REMOVABLE DOORS, SKINS, AND PANELS
SAE AMS 3276 : 2016	SEALING COMPOUND, INTEGRAL FUEL TANKS AND GENERAL PURPOSE, INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
SAE AMS 3102 : 2017	SEALING COMPOUND, POLYTHIOETHER RUBBER FAST CURING, LIGHT WEIGHT (SPECIFIC GRAVITY 0.78, MAX.) FOR INTEGRAL FUEL TANKS AND GENERAL PURPOSE, INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
SAE AMS S 83318 : 2016	SEALING COMPOUND, POLYSULFIDE TYPE, LOW TEMPERATURE CURING, QUICK REPAIR, INTEGRAL FUEL TANKS AND FUEL CELL CAVITIES
SAE AMS 3100 : 2013	ADHESION PROMOTER FOR POLYSULFIDE SEALING COMPOUNDS
SAE AMS S 8802 : 2015	SEALING COMPOUND, FUEL RESISTANT, INTEGRAL FUEL TANKS AND FUEL CELL CAVITIES
SAE AS 81550A : 2014	INSULATING COMPOUND, ELECTRICAL, EMBEDDING, REVERSION RESISTANT SILICONE
SAE AMS 3376 : 2015	SEALING COMPOUND, NON-CURING, FLUOROSILICONE GROOVE INJECTION TEMPERATURE AND FUEL RESISTANT
SAE AMS 3255 : 2017	SEALING TAPE, SHEET, OR GASKET, POLYTETRAFLUOROETHYLENE, EXPANDED (EPTFE) OIL AND WATER RESISTANT
SAE AMS S 4383 : 2015	SEALING COMPOUND, TOPCOAT, FUEL TANK BUNA-N TYPE
SAE AMS 3266 : 2017	SEALING COMPOUND, POLYTHIOETHER ELASTOMERIC TWO-PART ELECTRICALLY CONDUCTIVE
SAE AMS 3381 : 2014	SEALING COMPOUND, AIRCRAFT FIREWALL, NON-SILICONE
SAE AS 5127/1 : 2014	AEROSPACE STANDARD TEST METHODS FOR AEROSPACE SEALANTS TWO-COMPONENT SYNTHETIC RUBBER COMPOUNDS
SAE AMS 3167 : 2005	SOLVENTS, WIPE FOR CLEANING PRIOR TO APPLICATION OF PRIMER AND TOP COAT MATERIALS, OR SEALING COMPOUNDS
SAE AMS 3374 : 2013	SEALING COMPOUND AIRCRAFT FIREWALL, SILICONE
SAE AMS 3277 : 2015	SEALING COMPOUND, POLYTHIOETHER RUBBER, FAST CURING FOR INTEGRAL FUEL TANKS AND GENERAL PURPOSE, INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
SAE AMS 3284 : 2017	SEALING COMPOUND, LOW ADHESION, FOR REMOVABLE PANELS AND FUEL TANK INSPECTION PLATES

SAE AMS C 27725 : 2016	COATING, CORROSION PREVENTATIVE, FOR AIRCRAFT INTEGRAL FUEL TANKS, FOR USE TO 250 DEGREES F (121 DEGREES C)
SAE AMS 4049 : 2016	ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 5.6ZN - 2.5MG - 1.6CU - 0.23CR (ALCLAD 7075; -T6 SHEET - T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 4911 : 2014	TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED
SAE AS 5127/2 : 2014	TEST METHOD FOR AEROSPACE FIREWALL SEALANT FLAME PENETRATION
SAE AMS3819C : 2007	CLOTHS, CLEANING, FOR AIRCRAFT PRIMARY AND SECONDARY STRUCTURAL SURFACES
MIL-PRF-5425 Revision E:1998	PLASTIC SHEET, ACRYLIC, HEAT RESISTANT
MIL-PRF-85285 Revision E:2012	COATING: POLYURETHANE, AIRCRAFT AND SUPPORT EQUIPMENT
SAE AMS 4037 : 2014	ALUMINUM ALLOY, SHEET AND PLATE, 4.4CU - 1.5MG - 0.60MN (2024; -T3 FLAT SHEET, -T351 PLATE) SOLUTION HEAT TREATED
MIL-PRF-23377 Revision K:2012	PRIMER COATINGS: EPOXY, HIGH-SOLIDS
SAE AMS 4045 : 2016	ALUMINUM ALLOY SHEET AND PLATE 5.6ZN - 2.5MG - 1.6CU - 0.23CR 7075: (-T6 SHEET, -T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 5516 : 2012	STEEL, CORROSION-RESISTANT, SHEET, STRIP, AND PLATE, 18CR - 9.0NI (SAE 30302), SOLUTION HEAT TREATED
SAE AS 5127/1 : 2014	AEROSPACE STANDARD TEST METHODS FOR AEROSPACE SEALANTS TWO-COMPONENT SYNTHETIC RUBBER COMPOUNDS
MIL-DTL-81706 Revision B:2004	Chemical Conversion Materials for Coating Aluminum and Aluminum Alloys
MIL-DTL-5541 Revision F:2006	Chemical Conversion Coatings on Aluminum and Aluminum Alloys
SAE AMS P 83310 : 2016	PLASTIC SHEET, POLYCARBONATE, TRANSPARENT
SAE AMS 3100 : 2013	ADHESION PROMOTER FOR POLYSULFIDE SEALING COMPOUNDS
SAE AMS 3020 : 2013	OIL, REFERENCE, FOR 'L' STOCK RUBBER TESTING
MIL-PRF-23699 Revision G:2014	Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Numbers: O-152, O-154, O-156, and O-167
SAE AMS 2629 : 2017	FLUID, JET REFERENCE
MIL-PRF-25690 Revision B:1993	PLASTIC, SHEET AND FORMED PARTS, MODIFIED ACRYLIC BASE, MONOLITHIC, CRACK PROPAGATION RESISTANT
MIL-PRF-83282 Revision D:1997	HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537
TT-I-735 Revision A:1963	ISOPROPYL ALCOHOL
SAE AMS 3167 : 2005	SOLVENTS, WIPE FOR CLEANING PRIOR TO APPLICATION OF PRIMER AND TOP COAT MATERIALS, OR SEALING COMPOUNDS
MIL-PRF-85582 Revision E:2012	PRIMER COATINGS: EPOXY, WATERBORNE
SAE AMS 2471 : 2014	ANODIC TREATMENT OF ALUMINUM ALLOYS SULFURIC ACID PROCESS, UNDYED COATING
SAE AMS G 25667 : 2016	GLASS, MONOLITHIC, AIRCRAFT GLAZING
SAE AMS 4901 : 2015	TITANIUM SHEET, STRIP, AND PLATE, COMMERCIALLY PURE, ANNEALED, 70.0 KSI (485 MPA)