Skip to content
Please enter a keyword to search

  • SAE AS 5377 : 2000

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    NUT, SELF-LOCKING, 0.7500 THRU 1.5000 THREAD SIZES, UNS S66286, 160,000 PSI, 800 DEGREE F, UNJ THREAD - PROCUREMENT SPECIFICATION

    Available format(s): 

    Superseded date:  09-24-2020

    Language(s): 

    Published date:  01-01-2000

    Publisher:  SAE International

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 SCOPE
    2 REFERENCES
    3 TECHNICAL REQUIREMENTS
    4 QUALITY ASSURANCE PROVISIONS
    5 PREPARATION FOR DELIVERY
    6 ACKNOWLEDGEMENT
    7 REJECTIONS
    8 NOTES
    APPENDIX A MEASUREMENT OF PERPENDICULARITY VARIATION OF
               THE BEARING SURFACE
    APPENDIX B WRENCH TORQUE TEST
    APPENDIX C PERMANENT SET TEST
    APPENDIX D REUSABILITY TEST AT ROOM TEMPERATURE, AFTER
               BAKING
    APPENDIX E REUSABILITY TEST AT ROOM TEMPERATURE AS
               RECEIVED CONDITION
    APPENDIX F 3-CYCLE TEST AT ROOM TEMPERATURE

    Abstract - (Show below) - (Hide below)

    Covers the requirements for self-locking wrenchable nuts with thread sizes 0.7500 thru 1.5000 inches.

    General Product Information - (Show below) - (Hide below)

    Committee E-25
    Document Type Standard
    Publisher SAE International
    Status Superseded

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AS 5447 : 2012 ACCEPTANCE CRITERIA FOR NUTS - MAGNETIC, PARTICLE, FLUORESCENT PENETRANT, AND VISIBLE PENETRANT EXAMINATION
    MS 33787 : D WRENCHING ELEMENT, EXTERNAL SPLINE, DIMENSIONS FOR
    SAE AMS 5663 : 2016 NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 52.5NI - 19CR - 3.0MO - 5.1CB (NB) - 0.90TI - 0.50AL - 18FE CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 1775 DEGREES F (968 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED
    SAE AMS 5737 : 2012 STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED
    SAE AS 7467 : 2013 BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, STRESS RUPTURE RATED, PROCUREMENT SPECIFICATION
    MIL PRF 7808 : L LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE
    MIL W 8982 : D WRENCHES, SPLINED, HIGH STRENGTH, THIN WALL, GENERAL SPECIFICATION FOR
    SAE AMS 2759/3 : 2015 HEAT TREATMENT PRECIPITATION-HARDENING CORROSION-RESISTANT, MARAGING, AND SECONDARY HARDENING STEEL PARTS
    SAE AMS 5853 : 2012 STEEL, CORROSION AND HEAT-RESISTANT, BARS AND WIRE, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C) SOLUTION TREATED AND WORK-STRENGTHENED, 160 KSI (1103 MPA) TENSILE STRENGTH
    SAE AS 7466 : 2014 BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, FATIGUE RATED, PROCUREMENT SPECIFICATION
    GGG W 636 : E WRENCHES (BOX, OPEN END, AND COMBINATION)
    SAE AMS 5734 : 2012 STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C) SOLUTION HEAT TREATED
    SAE AS 870 : 2015 WRENCHING CONFIGURATION, BI-HEXAGONAL (12 POINT) DRIVE, DESIGN STANDARD FOR
    SAE AMS 5732 : 2012 STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED
    NASM 1312-6 : 0 FASTENER TEST METHODS, METHOD 6, HARDNESS
    SAE AS 8879 : 2004 SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER
    SAE AMS 5731 : 2012 STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1800 DEGREES F (982 DEGREES C) SOLUTION HEAT TREATED
    SAE AMS 2411 : 2013 PLATING, SILVER FOR HIGH TEMPERATURE APPLICATIONS
    SAE AS 5054 : 2012 AREAS FOR CALCULATING STRESS OF LOAD VALUES FOR EXTERNALLY AND INTERNALLY THREADED FASTENERS
    SAE AS 5443 : 2012 WRENCHING ELEMENT, SPLINE DRIVE - DIMENSIONS FOR
    SAE AIR 1471 : 2000 TORQUE TIGHTENING THREADED FASTENERS
    NASM 1312-8 : 2001 FASTENER TEST METHODS, METHOD 8, TENSILE STRENGTH
    SAE AS 1310 : 2012 FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective