• SAE J 1344 : 1997(S2017)

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    MARKING OF PLASTIC PARTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  03-28-2017

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. Scope
    2. References
    3. Description
    4. Use of Marking Symbols
    5. Notes
    APPENDIX A - REQUEST TO ADD NEW MARKING SYMBOLS AND/OR
                 TRADEMARKS
    APPENDIX B - PROCESS FLOW CHART - ADDING NEW SYMBOLS TO J1344
    APPENDIX C - CROSS REFERENCE SYMBOLS TO COMMON NAMES/TRADEMARKS
    APPENDIX D - CROSS REFERENCE LIST SPI/PBI PLASTIC CONTAINER MARKING
                 CODES TO SAE PART MARKING SYMBOLS
    APPENDIX E - CROSS REFERENCE LISTING - TRADEMARKS/SUPPLIERS
    APPENDIX F - SYMBOLS FOR COMMONLY USED AUTOMOTIVE ELASTOMERS
                 (BASED ON ISO 1629)

    Abstract - (Show below) - (Hide below)

    Gives a system for marking plastic parts to designate the type of material from which the part was fabricated.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes JAGUAR JAS 02.01.13. (07/2003)
    Document Type Revision
    Product Note STABILIZED VERSION IS NOW AVAILABLE
    Publisher SAE International
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE USCAR 33 : 2013 SPECIFICATION FOR TESTING AUTOMOTIVE LED MODULES
    UL 7006 : 1ED 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD ROOM AIR CONDITIONING APPLIANCES
    R7004-17 Sustainability standard for household cooking appliances (Binational standard with AHAM 7004-2017 and UL 7004)
    CSA R7003 : 2016 SUSTAINABILITY STANDARD FOR HOUSEHOLD CLOTHES WASHERS
    CSA SPE 7005 : 2016 SUSTAINABILITY STANDARD FOR HOUSEHOLD CLOTHES DRYING APPLIANCES
    CSA R7006 : 2018 SUSTAINABILITY STANDARD FOR HOUSEHOLD ROOM AIR CONDITIONING APPLIANCES
    UL 7008 : 1ED 2018 SUSTAINABILITY STANDARD FOR HOUSEHOLD DEHUMIDIFIER APPLIANCES
    SAE J 1639 : 1995(S2017) CLASSIFICATION SYSTEM FOR AUTOMOTIVE POLYAMIDE (PA) PLASTICS
    SAE J 1555 : 2016 RECOMMENDED PRACTICE FOR OPTIMIZING AUTOMOBILE DAMAGEABILITY AND REPAIRABILITY
    CSA SPE 7007 : 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD MICROWAVE OVEN APPLIANCES
    SAE J 2642 : 2017 RECOMMENDED PRACTICE FOR DEVELOPING SPECIFICATIONS FOR AUTOMOTIVE THERMOPLASTIC MATERIALS
    SAE J 1345 : 1995 AUTOMOTIVE PLASTIC PARTS SPECIFICATION
    UL 7007 : 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD MICROWAVE OVEN APPLIANCES
    R7005-17 Sustainability standard for household clothes drying appliances (Binational standard with AHAM 7005-2017 and UL 7005)
    UL 7004 : 2ED 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD COOKING APPLIANCES
    CSA SPE 7006 : 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD ROOM AIR CONDITIONING APPLIANCES
    CSA SPE 7008 : 2018 SUSTAINABILITY STANDARD FOR HOUSEHOLD DEHUMIDIFIER APPLIANCES
    SAE J 2028 : 2016 FRONT-WHEEL-DRIVE CONSTANT VELOCITY JOINT BOOT SEALS
    SAE USCAR 27 : 2007 SPECIFICATION FOR TESTING GAS DISCHARGE LIGHT SOURCE SUBSYSTEM
    AHAM 7004 : 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD COOKING APPLIANCES
    SAE J 2594 : 2016 RECOMMENDED PRACTICE TO DESIGN FOR RECYCLING PROTON EXCHANGE MEMBRANE (PEM) FUEL CELL SYSTEMS
    UL 7003 : 2ED 2016 SUSTAINABILITY STANDARD FOR HOUSEHOLD CLOTHES WASHERS
    UL 7005 : 2ED 2017 SUSTAINABILITY STANDARD FOR HOUSEHOLD CLOTHES DRYING APPLIANCES

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 11469:2016 Plastics — Generic identification and marking of plastics products
    VDA 260 : 2007 COMPONENTS OF MOTOR VEHICLES - MARKING OF MATERIAL
    ISO 1043-2:2011 Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    ISO 1629:2013 Rubber and latices Nomenclature
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective