• SAE J 617 : 2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    ENGINE FLYWHEEL HOUSING AND MATING TRANSMISSION HOUSING FLANGES

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-06-2020

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. REFERENCES
    3. DIMENSIONS AND TOLERANCES
    4. ENGINE FLYWHEEL HOUSINGS
    5. MATING TRANSMISSION HOUSING FLANGES
    6. NOTES

    Abstract - (Show below) - (Hide below)

    This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges.

    General Product Information - (Show below) - (Hide below)

    Document Type Revision
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE J 1033 : 2012 PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS, AND FLYWHEEL HOUSING ADAPTERS
    SAE J 2407 : 2017 CLUTCH INSTALLATION AND RELEASE LINKAGE REQUIREMENTS FOR TRUCK AND BUS APPLICATION
    SAE J 2408 : 2018 CLUTCH REQUIREMENTS FOR HIGH-TORQUE TRUCK AND BUS ENGINES
    SAE J 1806 : 2017 CLUTCH DIMENSIONS FOR TRUCK AND BUS APPLICATIONS
    SAE J 2555 : 2017 Vehicle Idle Gear Rattle Evaluation Procedure
    SAE J 1463 : 2012 PULL-TYPE CLUTCH TRANSMISSION INSTALLATION DIMENSIONS
    SAE J 620 : 2012 FLYWHEELS FOR INDUSTRIAL ENGINES USED WITH INDUSTRIAL POWER TAKE-OFFS EQUIPPED WITH DRIVING-RING TYPE OVERCENTER CLUTCHES AND ENGINE-MOUNTED MARINE GEARS AND SINGLE BEARING ENGINE-MOUNTED POWER GENERATORS
    HI 1.3 : 2013 ROTODYNAMIC CENTRIFUGAL PUMPS FOR DESIGN AND APPLICATION
    SAE J 2469 : 2017 CLUTCH APPLICATION POWERTRAIN STARTABILITY RATING REQUIREMENTS FOR TRUCK AND BUS APPLICATIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    ANSI Y14.5 : 1973 DIMENSIONING AND TOLERANCING FOR ENGINEERING DRAWINGS
    SAE J 621 : 2012 INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING TYPE OVERCENTER CLUTCHES
    SAE J 543 : 1995 STARTING MOTOR PINIONS AND RING GEARS
    ANSI B11 : 2008 GENERAL SAFETY REQUIREMENTS COMMON TO ANSI B11 MACHINES
    SAE J 927 : 1995 FLYWHEELS FOR ENGINE MOUNTED TORQUE CONVERTERS
    SAE J542:1991 STARTING MOTOR MOUNTINGS
    ISO 7649:1991 Clutch housings for reciprocating internal combustion engines Nominal dimensions and tolerances
    SAE J 616 : 1995 ENGINE FOOT MOUNTING (FRONT AND REAR)
    ISO 7648:1987 Flywheel housings for reciprocating internal combustion engines Nominal dimensions and tolerances
    SAE J 1033 : 2012 PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS, AND FLYWHEEL HOUSING ADAPTERS
    SAE J 1172 : 2012 ENGINE FLYWHEEL HOUSINGS WITH SEALED FLANGES
    SAE J 615 : 1995 ENGINE MOUNTINGS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective