• There are no items in your cart

UNE-EN 14364:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
Available format(s)

Hardcopy , PDF

Superseded date

03-23-2022

Language(s)

Spanish, Castilian, English

Published date

02-04-2015

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 General requirements
  4.1 Classification
      4.1.1 Categories
      4.1.2 Nominal size
      4.1.3 Nominal stiffness
      4.1.4 Nominal pressure
  4.2 Materials
      4.2.1 General
      4.2.2 Reinforcement
      4.2.3 Resin
      4.2.4 Aggregates and fillers
      4.2.5 Elastomers
      4.2.6 Metals
  4.3 Wall construction
      4.3.1 Inner layer
      4.3.2 Structural layer
      4.3.3 Outer layer
  4.4 Appearance
  4.5 Reference conditions for testing
      4.5.1 Temperature
      4.5.2 Properties of water for testing
      4.5.3 Loading conditions
      4.5.4 Preconditioning
      4.5.5 Measurement of dimensions
  4.6 Elapsed time for determination of long-term properties, (x)
  4.7 Joints
      4.7.1 General
      4.7.2 Types of joint
      4.7.3 Flexibility of the jointing system
      4.7.4 Sealing ring
      4.7.5 Adhesives
5 Pipes
  5.1 Geometrical characteristics
      5.1.1 Diameter
      5.1.2 Wall thickness
      5.1.3 Length
  5.2 Mechanical characteristics
      5.2.1 Initial specific ring stiffness
      5.2.2 Long-term specific ring stiffness under wet conditions
      5.2.3 Initial resistance to failure in a deflected condition
      5.2.4 Ultimate long-term resistance to failure in a deflected
            condition
      5.2.5 Initial specific longitudinal tensile strength
      5.2.6 Initial failure and design pressures for pressure pipes
      5.2.7 Long-term failure pressure
      5.2.8 Resistance to strain corrosion
  5.3 Marking
6 Fittings
  6.1 General
      6.1.1 Diameter series
      6.1.2 Nominal pressure (PN)
      6.1.3 Nominal stiffness (SN)
      6.1.4 Joint type
      6.1.5 Pipe type
      6.1.6 Mechanical characteristics of fittings
      6.1.7 Installed leak-tightness of fittings
      6.1.8 Dimensions
  6.2 Bends
      6.2.1 Classification of bends
      6.2.2 Dimensions and tolerances of bends
  6.3 Branches
      6.3.1 Classification of branches
      6.3.2 Dimensions and tolerances of branches
  6.4 Reducers
      6.4.1 Classification of reducers
      6.4.2 Dimensions and tolerances of reducers
      6.4.3 Mechanical characteristics of tapered section laminate
  6.5 Saddles
      6.5.1 Classification of saddles
      6.5.2 Dimensions and tolerances of saddles
  6.6 Flanged adaptors
      6.6.1 Classification of flanged adaptors
      6.6.2 Dimensions and tolerances of flanged adaptors
  6.7 Marking
7 Joint performance
  7.1 General
      7.1.1 Interchangeability
      7.1.2 Test temperature
  7.2 Dimensions
  7.3 Non-end-load-bearing flexible joints with elastomeric
      sealing rings
      7.3.1 General
      7.3.2 Requirements
      7.3.3 Number of test pieces for type test purposes
      7.3.4 Test pieces
  7.4 End-load-bearing flexible joints with elastomeric sealing
      rings
      7.4.1 General
      7.4.2 Performance requirements for locked-socket-and-spigot
            joints with elastomeric sealing rings
  7.5 Wrapped or cemented joints
      7.5.1 General
      7.5.2 Performance requirements
      7.5.3 Number of test pieces for type test purposes
      7.5.4 Test pieces
  7.6 Bolted flange joints
      7.6.1 General
      7.6.2 Performance requirements
      7.6.3 Number of test pieces for type test purposes
      7.6.4 Test pieces
      7.6.5 Joint assembly details
      7.6.6 Torque resistance
Annex A (normative) Test method for the resistance to bending and
        pressure of end-thrust loaded joints in pipe systems
      A.1 Principle
      A.2 Apparatus
      A.3 Test pieces
      A.4 Test temperature
      A.5 Calculation of the bending load F
          A.5.1 General
          A.5.2 Calculation of F, if applied in the horizontal plane
          A.5.3 Calculation of F, if applied in the vertical plane
      A.6 Procedure
      A.7 Test report
Bibliography

Describes the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together.

Committee
CTN 53/SC 2
DevelopmentNote
Supersedes UNE EN 1115-1, UNE EN 1115-3, UNE EN 1115-5, UNE EN 1636-3 & UNE EN 1636-5. (05/2008)
DocumentType
Standard
Pages
66
PublisherName
Asociacion Espanola de Normalizacion
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NBN EN 14364 : 2013 Identical
NEN EN 14364 : 2013 Identical
NS EN 14364 : 2013 Identical
I.S. EN 14364:2013 Identical
SN EN 14364 : 2013 Identical
BS EN 14364:2013 Identical
EN 14364:2013 Identical
NF EN 14364 : 2013 Identical
DIN EN 14364:2013-05 Identical
DIN EN 14364 E : 2013 Identical

ISO 8521:2009 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength
EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
ISO 7432:2002 Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
EN ISO 2078:1994/A1:2015 TEXTILE GLASS - YARNS - DESIGNATION (ISO 2078:1993/AMD 1:2015)
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
ISO/TR 10465-3:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits
ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
ISO 1452-3:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 3: Fittings
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
CEN/TS 14632:2012 Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
ISO 527-5:2009 Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
EN 1447:2009+A1:2010 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
EN 476:2011 General requirements for components used in drains and sewers
ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
ISO 2078:1993 Textile glass Yarns Designation
ISO 8483:2003 Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints
ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
ISO 10466:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring deflection
ISO 10471:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
EN 1119:2009 Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements
EN ISO 1452-3:2010 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings (ISO 1452-3:2009, corrected version 2010-03-01)
ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
CEN/TS 14807:2013 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines
ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
CEN/TS 14578:2013 Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation

View more information
US$114.01
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.