• There are no items in your cart

UNI EN 528 : 2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

RAIL DEPENDENT STORAGE AND RETRIEVAL EQUIPMENT - SAFETY REQUIREMENTS
Superseded date

08-23-2022

Published date

01-01-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant and relevant hazards
5 Safety requirements and/or protective measures
   for all types of S/R machines
   5.1 Introduction
   5.2 Control position
   5.3 Control equipment
   5.4 Hoist unit
   5.5 Travel unit
   5.6 Load handling devices
   5.7 Electrical equipment
   5.8 Transfer device
   5.9 Maintenance repair and fault clearance
   5.10 Machine environment
6 Additional requirements for manual operated machines
   6.1 General
   6.2 Onboard control position
   6.3 Control equipment
   6.4 Hoist unit
   6.5 Acceleration and deceleration
   6.6 Protection of operators in an aisle containing
        two or more manually operated machines
7 Particular requirements for machines without an
   on-board operator
   7.1 General
   7.2 External control position (control desk)
   7.3 Control equipment
   7.4 Hoist unit
   7.5 Load handling devices
   7.6 Escape
8 Installation
   8.1 Erection and dismantling on site
   8.2 Commissioning
9 Verification of safety requirements and/or measures
   9.1 Examination
   9.2 Written record
   9.3 EMC
   9.4 Noise
   9.5 Load tests
10 Information for use
   10.1 General
   10.2 Instruction handbook
   10.3 Minimum markings
   10.4 Conditions for the safe operation of equipment
   10.5 Maintenance, inspection and testing
Annex A (informative) - Illustration of types of machines
        and transfer equipment
Annex B (informative) - Means of separation within
        racking
Annex C (normative) - Safety levels according to
        EN ISO 13849-1
Annex D (informative) - Examples for the design of
        load entry/exit points to prevent or deter
        access to danger areas or protect persons
        in accordance with 5.10.4
      D.1 General
      D.2 Measures against access between the conveyor
          and fixed guard
      D.3 Load entry/exit opening height
      D.4 Measures which deter access
      D.5 Measures that prevent access
      D.6 Protecting devices
Annex E (normative) - Verification of safety requirements
        and/or measures
Annex ZA (informative) - Relationship between this
         European Standard and the Essential Requirements
         of EU Directive Machinery 98/37/EC
Annex ZB (informative) - Relationship between this
         European Standard and the Essential Requirements
         of EU Directive Machinery 2006/42/EC
Bibliography

Applicable to all types of S/R machines, restricted to the rails on which they travel within and outside the aisles, which embody lifting means and may embody lateral handling facilities, for the storage and retrieval of unit loads and/or long goods such as bar materials and/or for order picking or similar duties.

DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ONORM EN 528 : 2009 Identical
EN 528:2008 Identical
DIN EN 528:2009-02 Identical
UNE-EN 528:2009 Identical
NS EN 528 : 2ED 2008 Identical
NF EN 528 : 2008 Identical
NBN EN 528 : 2009 Identical
NEN EN 528 : 2008 Identical
BS EN 528:2008 Identical
I.S. EN 528:2008 Identical
SN EN 528 : 2009 Identical

ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
ISO 4308-1:2003 Cranes and lifting appliances Selection of wire ropes Part 1: General
EN 12385-4:2002+A1:2008 Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
ISO 14122-3:2016 Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
ISO 14122-1:2016 Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
EN 61000-6-3:2007/A1:2011/AC:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010)
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
EN 999:1998+A1:2008 Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN 61310-3:2008 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
IEC 61310-3:2007 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
EN 1760-1:1997+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
IEC 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN 81-1:1998+A3:2009 Safety rules for the construction and installation of lifts - Part 1: Electric lifts
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN 13411-3:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
ISO 14122-4:2016 Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
EN 574:1996+A1:2008 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
DIN 15350:1992-04 STORAGE AND RETRIEVAL MACHINES - RULES FOR CALCULATIONS OF STEEL STRUCTURES
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
IEC 61000-6-3:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
EN 1263-1:2014 Temporary works equipment - Safety nets - Part 1: Safety requirements, test methods
EN 1263-2:2014 Temporary works equipment - Safety nets - Part 2: Safety requirements for the positioning limits
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
CLC/TS 61496-3:2008 Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
EN 61000-6-2:2005/corrigendum:2005 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
IEC 61496-3:2008 Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
ZH 1/361 : 1978 GUIDELINES FOR APPLIANCES AND SYSTEMS FOR SHELF OPERATION
EN ISO 14122-4:2016 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
EN 81-2 : 1998 + A3 2009 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 2: HYDRAULIC LIFTS
EN ISO 14122-2:2016 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
EN 13411-6:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
EN 363:2008 Personal fall protection equipment - Personal fall protection systems
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 1760-2:2001+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
EN 1760-3:2004+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices
ISO 14122-2:2016 Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways
EN 795:2012 Personal fall protection equipment - Anchor devices
ISO 13050:2014 Synchronous belt drives Metric pitch, curvilinear profile systems G, H, R and S, belts and pulleys
EN ISO 14122-1:2016 Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.