• UNI EN ISO 11296-4 : 2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES

    Available format(s): 

    Superseded date:  08-29-2022

    Language(s): 

    Published date:  01-01-2011

    Publisher:  Ente Nazionale Italiano di Unificazione (UNI)

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Pipes at the "M" stage
    6 Fittings at the "M" stage
    7 Ancillary components
    8 Fitness for purpose of the installed lining system at the
      "I" stage
    9 Installation practice
    Annex A (informative) - CIPP components and their
            functions
    Annex B (normative) - Cured-in-place pipes - Modifications
            to ISO 178 for flexural testing
    Annex C (normative) - Cured-in-place pipes - Test method
            for the determination of long-term flexural modulus
            under wet conditions
    Annex D (normative) - Cured-in-place pipes - Determination
            of the creep factor under dry conditions from a
            three-point flexural test
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes UNI EN 13566-4. (09/2011)
    Document Type Standard
    Publisher Ente Nazionale Italiano di Unificazione (UNI)
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 25780:2011 Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques
    ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP)
    ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
    ISO 10928:2016 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Methods for regression analysis and their use
    ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
    ISO 75-2:2013 Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 13002:1998 Carbon fibre Designation system for filament yarns
    ISO 8513:2016 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the initial longitudinal tensile strength
    ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
    ISO 7684:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the creep factor under dry conditions
    ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
    EN 14364:2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
    ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective