Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • AGMA 2001 : D

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH

    Available format(s):  Hardcopy

    Language(s):  English

    Published date:  01-01-2004

    Publisher:  American Gear Manufacturers Association

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references, definitions and symbols
    3 Application
    4 Criteria for tooth capacity
    5 Fundamental rating formulas
    6 Geometry factors, I and J
    7 Transmitted tangential load, W[t]
    8 Dynamic factor, K[v]
    9 Overload factor, K[o]
    10 Service factor
    11 Safety factors, S[H] and S[F]
    12 Elastic coefficient, C[p]
    13 Surface condition factor, C[f]
    14 Hardness ratio factor, C[H]
    15 Load distribution factor, K[m]
    16 Allowable stress numbers, s[ac] and s[at]
    17 Stress cycle factors, Z[N] and Y[N]
    18 Reliability factor, K[R]
    19 Temperature factor, K[T]
    20 Size factor, K[s]
    Bibliography
    Annexes
    A Method for determination of dynamic factor with AGMA 2000-A88
    B Rim thickness factor, K[B]
    C Application analysis
    D Discussion of the analytical face or longitudinal load
      distribution factor
    E Gear material fatigue life
    F Controlling section size considerations for through hardened
      gearing
    Figures
    Tables

    Abstract - (Show below) - (Hide below)

    Describes a comprehensive method for rating the pitting resistance and bending strength of spur and helical involute gear pairs. Includes detailed discussions of factors influencing gear survival and calculation methods.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes AGMA 218.01 (03/2002) Supplement is available separately, see record AGMA 925. (02/2015) Metric Edition of this standard is available as AGMA 2101. (04/2016)
    Document Type Standard
    Publisher American Gear Manufacturers Association
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    MIL L 80277 : 0 LATHES, PRECISION, TOOLROOM, VARIABLE SPEED, 11-INCH THROUGH 13-INCH
    03/314804 DC : DRAFT SEP 2003 BS ISO 6336-3 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 3: CALCULATION OF TOOTH BENDING STRENGTH
    BS ISO 6336-3:2006 CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 3: CALCULATION OF TOOTH BENDING STRENGTH
    MIL L 23251 : E LATHES, ENGINE AND TOOLROOM 2516 AND 3220
    CSA B354.5 : 2007 : R2016 MAST-CLIMBING WORK PLATFORMS
    AGMA 6023 : REV A : 1988 : R2000 DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES
    MIL S 80271 : A SHEARING MACHINE, METAL SQUARING MECHANICAL DRIVE
    AGMA 1012 : 2005 GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS
    B354.12-17 Design, calculations, safety requirements, and test methods for mast climbing transport platforms (MCTPs)
    03/314803 DC : DRAFT SEP 2003 ISO 6336-2 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 2: CALCULATION OF SURFACE DURABILITY (PITTING)
    API SPEC 11E : 2013 SPECIFICATION FOR PUMPING UNITS
    AGMA 912 : A MECHANISMS OF GEAR TOOTH FAILURE
    AGMA 6010 : REV F : 1997 : R2003 STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES
    AGMA 6001 : REV D : 1997 DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
    API 2C RUSSIAN : 2004 SPECIFICATION FOR OFFSHORE PEDESTAL MOUNTED CRANES
    ISO/TS 10303-5001:2010 Industrial automation systems and integration — Product data representation and exchange — Part 5001: Guidance on the usage of ISO 10303-214 for gear units
    ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
    B354.9-17 Design, calculations, safety requirements, and test methods for mast climbing work platforms (MCWPs)
    API 11E RUSSIAN : 2013 SPECIFICATION FOR PUMPING UNITS
    MIL M 80255 : B MACHINING CENTERS, VERTICAL, SINGLE SPINDLE, COMPUTER NUMERICAL CONTROL (CNC)
    AGMA 6023 : REV A : 1988 : R1993 DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES
    AGMA 6010 : REV F : 1997 STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES
    ISO 6336-3:2006 Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength
    API 613:2003 SPECIAL PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
    API SPEC 11E CHINESE : 2013 SPECIFICATION FOR PUMPING UNITS
    ISO 6336-2:2006 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting)
    06/30157507 DC : 0 BS ISO 10431 - PETROLEUM AND NATURAL GAS INDUSTRIES - PUMPING UNITS - SPECIFICATION
    BS ISO 6336-2:2006 CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 2: CALCULATION OF SURFACE DURABILITY (PITTING)
    AGMA 923 : B METALLURGICAL SPECIFICATIONS OF STEEL GEARING
    SAE J 1619 : 2017 SINGLE TOOTH GEAR BENDING FATIGUE TEST
    CSA B354.5 : 2007 : INC : UPD 1 : 2008 : R2011 MAST-CLIMBING WORK PLATFORMS
    BS ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Basic principles, introduction and general influence factors
    CSA B354.5:2007 MAST-CLIMBING WORK PLATFORMS
    AGMA 6001 : REV D : 1997 : R2003 DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
    AGMA 937 : A2012(R2017) AEROSPACE BEVEL GEARS
    04/30126837 DC : DRAFT DEC 2004 BS ISO 6336-1 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 1: BASIC PRINCIPLES, INTRODUCTION AND GENERAL INFLUENCE FACTORS
    MIL L 80007 : E LATHES, TOOLROOM, 11-INCH THROUGH 13-INCH
    API 2C : 2012 OFFSHORE PEDESTAL-MOUNTED CRANES

    Standards Referencing This Book - (Show below) - (Hide below)

    AGMA 933 : B BASIC GEAR GEOMETRY
    AGMA 2015-1 : A ACCURACY CLASSIFICATION SYSTEM - TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS
    AGMA 6011 : I SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS
    AGMA 246.02 : A RECOMMENDED PROCEDURE FOR CARBURIZED AEROSPACE GEARING
    ISO/TR 10495:1997 Cylindrical gears Calculation of service life under variable loads Conditions for cylindrical gears according to ISO 6336
    ASTM A 291 : 2003 Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears
    AGMA 427.01 : 0 INFORMATION SHEET - SYSTEMS CONSIDERATIONS FOR CRITICAL SERVICE GEAR DRIVES
    AGMA 2000 : A GEAR CLASSIFICATION AND INSPECTION HANDBOOK - TOLERANCES AND MEASURING METHODS FOR UNASSEMBLED SPUR AND HELICAL GEARS (INCLUDING METRIC EQUIVALENTS)
    AGMA 1010 : E APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE
    AGMA 2007 : C GEARS - SURFACE TEMPER ETCH INSPECTION AFTER GRINDING
    SAE AMS 2301 : 2015 STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
    AGMA 925 : A EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS
    AGMA 908 : B GEOMETRY FACTORS FOR DETERMINING THE PITTING RESISTANCE AND BENDING STRENGTH OF SPUR, HELICAL AND HERRINGBONE GEAR TEETH
    AGMA 9005 : E INDUSTRIAL GEAR LUBRICATION
    ASTM A 535 : 1985 Specification for Special-Quality Ball and Roller Bearing Steel (Withdrawn 1998)
    SAE AMS 2300 L : 2015 STEEL CLEANLINESS, PREMIUM AIRCRAFT-QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
    AGMA 927 : A LOAD DISTRIBUTION FACTORS - ANALYTICAL METHODS FOR CYLINDRICAL GEARS
    ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
    AGMA 6033 : B MATERIALS FOR MARINE PROPULSION GEARING
    AGMA 2004 : C GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL
    AGMA 1012 : 2005 GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS
    ASTM A 534 : 2017 : REDLINE Standard Specification for Carburizing Steels for Anti-Friction Bearings
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more