ASTM C 534/C534M : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form
Hardcopy , PDF
27-08-2020
English
01-03-2019
This specification covers preformed flexible elastomeric cellular-thermal insulation in sheet and tubular form.
1.1This specification covers preformed flexible elastomeric cellular-thermal insulation in sheet and tubular form. Grade 1 covers materials to be used on commercial or industrial systems with operating temperatures from –183 to 104°C [–297 to 220°F], Grade 2 covers material used on industrial systems with operating temperatures from –183 to 150°C [–297 to 300°F], and Grade 3 covers material used on industrial systems with operating temperatures from –183 to 120°C [–297 to 250°F] where halogens are not permitted.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
C 16
|
| DocumentType |
Standard
|
| Pages |
6
|
| ProductNote |
THIS STANDARD ALSO REFERES TO : CAN/ULC-S102
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 1045 : 2019 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 1114 : 2006 : R2013 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1114 : 2006 : R2019 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1045 : 2007 : R2013 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 1304 : 2008 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM E 2231 : 2002 : EDT 1 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1763 : 2019 : REDLINE | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM C 1427 : 2007 : EDT 1 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM C 1427 : 2012 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM C 1304 : 2008 : R2013 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 1304 : 2018 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 1058 : 1997 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM C 1058 : 2003 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM C 1763 : 2020 | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM E 2231 : 2014 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1427 : 1999 : REV A | Specification for Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM C 1763 : 2016 | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM D 1622 : 2008 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM E 2231 : 2019 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1114 : 2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1045 : 2001 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM D 1667 : 1976 : R1990 | Standard Specification for Flexible Cellular MaterialsÐVinyl Chloride Polymers and Copolymers (Closed-Cell Foam) |
| ASTM D 1667 : 2005 | Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam) |
| ASTM D 1667 : 1997 | Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam) |
| ASTM C 1763 : 2014 | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM D 1622 : 2003 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM E 2231 : 2007 : REV A | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 2231 : 2002 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1304 : 1995 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 1763 : 2019 : EDT 1 | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM C 1427 : 2016 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM E 2231 : 2009 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1114 : 2000 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM E 2231 : 2007 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM D 1622 : 1998 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM E 2231 : 2018 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM D 1667 : 2005 : R2011 | Standard Specification for Flexible Cellular Materials<char: emdash>Poly (Vinyl Chloride) Foam (Closed-Cell) |
| ASTM C 1114 : 2000 : R2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1045 : 1997 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 1427 : 2004 | Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM C 1427 : 2013 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM C 1763 : 2019 | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
| ASTM C 1058 : 2003 : R2008 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM D 1667 : 2017 | Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell) |
| ASTM C 1427 : 2007 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
| ASTM E 2231 : 2015 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1045 : 2007 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM D 1622 : 1993 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.