ASTM D 3276 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Painting Inspectors (Metal Substrates)
Hardcopy , PDF
12-03-2017
English
01-09-2015
1.1This guide is intended as an information aid to painting inspectors in carrying out their task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to the specification of a particular job.
Note 1:For additional helpful information, refer to the following documents:
Manual of Coating Work for Light-Water Nuclear Power Plant Primary Containment and Other Safety-Related Facilities 2
New Concepts for Coating Protection of Steel Structures3
D16 Terminology for Paint, Related Coatings, Materials, and Applications 4
D4538 Terminology Relating to Protective Coatings and Lining Work for Power Generation Facilities 4
Steel Structures Painting Manual Vol 1 Good Painting Practice 6
Steel Structures Painting Manual Vol 2 Systems and Specifications 6
Manufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application)
Safety Data Sheets (needed to ensure that personnel take necessary precautions in handling hazardous materials). Available from Materials manufacturer.
1.2Certain industries or owners may require certified inspection personnel. See Guide D4537 for establishing procedures to certify inspectors for coatings work in nuclear facilities.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This guide is arranged in the following order:
| Section | |
| Referenced Documents | 2 |
| ASTM Standards | 2.1 |
| OSHA Standards | 2.2 |
| Steel Structures Painting Council Publications | 2.3 |
| International Standards Organization (ISO) | 2.4 |
| ASTM Adjuncts | 2.6 |
| Significance and Use | 3 |
| Preparation for Inspection | 4 |
| Surface Preparation Methods and Requirements | 5 |
| Surface Preparation | 5.1 |
| Pictorial Standard D2200 | 5.1.1 |
| Factors Affecting Coating Performance | 5.2 |
| Cleanliness | 5.2.1 |
| Mill Scale | 5.2.2 |
| Surface Profile | 5.2.3 |
| Sharp Edges | 5.2.4 |
| Cleaning Procedures | 5.3 |
| Chemical Cleaning | 5.3.1 |
| Solvent Vapor Cleaning | 5.3.1.1 |
| Hand Tool Cleaning | 5.3.2 |
| Power Tool Cleaning | 5.3.3 |
| Power Tool Cleaning to Bare Metal | 5.3.4 |
| Commercial Grade Power Tool Cleaning | 5.3.4.4 |
| Blast Cleaning | 5.3.5 |
| Pressurized Water Cleaning | 5.3.6 |
| Cleaning and Preparation of Various Surfaces | 5.4 |
| Steel Surfaces | 5.4.1 |
| Galvanized Surfaces | 5.4.2 |
| Aluminum Surfaces | 5.4.3 |
| Precautions in Preparing Unpainted and Previously | |
| Painted Surfaces | 5.4.4 |
| Inspection of Surfaces Prior to Field Painting | 5.5 |
| New Construction | 5.5.1 |
| Maintenance Repainting | 5.5.2 |
| Coating Storage and Handling | 6 |
| Storage of Coating and Thinner | 6.1 |
| Mixing of Coatings | 6.2 |
| Thinning | 6.3 |
| Initial Samples | 6.3.1 |
| Thinning of Coating | 6.3.2 |
| Sampling of Thinned Coating | 6.3.3 |
| Heating of Coating | 6.4 |
| Weather Considerations | 7 |
| Drying | 7.1 |
| Low Temperature | 7.2 |
| High Temperature | 7.3 |
| Moisture | 7.4 |
| Wind | 7.5 |
| Coating Application | 8 |
| Residual Contaminants | 8.1 |
| Quality Assurance | 8.2 |
| Film Defects | 8.2.1 |
| Brush Application | 8.3 |
| Spray Application | 8.4 |
| Roller Application | 8.5 |
| Miscellaneous Methods | 8.6 |
| Rate of Application | 8.7 |
| Additional Considerations | 9 |
| Ventilation | 9.1 |
| Shopcoat Repair | 9.2 |
| Painting Schedule | 9.3 |
| Film Integrity | 9.4 |
| Recoat Time | 9.5 |
| Coating System Failure | 9.6 |
| Inspection Equipment | 10 |
| General | 10.1 |
| Surface Profile Gages | 10.1.1 |
| Adhesion of Existing Coating | 10.1.2 |
| Portable Pull-Off Adhesion Testers | 10.1.3 |
| Field Inspection Equipment | 10.2 |
| Drying and Curing Times | 10.2.1 |
| Thermometers | 10.2.1.1 |
| Relative Humidity and Dew Point | 10.2.1.2 |
| Wet-Film Thickness Gages | 10.2.2 |
| Interchemical Gage | 10.2.2.1 |
| Notched Gage | 10.2.2.2 |
| Dry-Film Thickness Gages | 10.2.3 |
| Nondestructive Film Thickness Gages | 10.2.3.1 |
| Magnetic-Type Gages | 10.2.3.2 |
| Current-Type Gages | 10.2.3.3 |
| Destructive Thickness Gage | 10.2.3.4 |
| Holiday Detectors | 10.2.4 |
| Comparison of Surface Preparation | |
| Specifications | Table 1 |
| Comparison of Water Jetting Standards | Table 2 |
| Inspection Checklist | Appendix X1 |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.