ASTM D 4378 : 2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
Hardcopy , PDF
22-03-2024
English
08-08-2022
1.1This practice covers the requirements for the effective monitoring of mineral turbine oils in service in steam and gas turbines, as individual or combined cycle turbines, used for power generation. This practice includes sampling and testing schedules to validate the condition of the lubricant through its life cycle and by ensuring required improvements to bring the present condition of the lubricant within the acceptable targets. This practice is not intended for condition monitoring of lubricants for auxiliary equipment; it is recommended that the appropriate practice be consulted (see Practice D6224).
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 02
|
| DocumentType |
Standard Practice
|
| Pages |
19
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 8112 : 2022 | Standard Guide for Obtaining In-Service Samples of Turbine Operation Related Lubricating Fluid |
| ASTM D 7669 : 2020 | Standard Guide for Practical Lubricant Condition Data Trend Analysis |
| ASTM D 7720 : 2021 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 6224 : 2022 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
| ASTM D 7843 : 2021 | Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry |
| ASTM D 7590 : 2009 : R2014 | Standard Guide for Measurement of Remaining Primary Antioxidant Content In In-Service Industrial Lubricating Oils by Linear Sweep Voltammetry |
| ASTM D 6971 : 2009 : R2014 | Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry |
| ASTM D 8185 : 2018 | Standard Guide for In-Service Lubricant Viscosity Measurement |
| ASTM D 6439 : 2011 : R2017 | Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems |
| ASTM D 8185 : 2023 | Standard Guide for In-Service Lubricant Viscosity Measurement |
| ASTM D 8506 : 2023 | Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems |
| ASTM D 7590 : 2022 | Standard Guide for Measurement of Remaining Primary Antioxidant Content In In-Service Industrial Lubricating Oils by Linear Sweep Voltammetry |
| ASTM D 6810 : 2022 | Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 974 : 2014 : EDT 2 | Standard Test Method for Acid and Base Number by Color-Indicator Titration |
| ASTM D 6439 : 2023 | Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems |
| ASTM D 4898 : 2016 | Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis |
| ASTM F 312 : 2008 : R2023 | Standard Test Methods for Microscopical Sizing and Counting Particles from Aerospace Fluids on Membrane Filters |
| ASTM D 7647 : 2024 | Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction |
| ASTM D 6971 : 2022 | Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry |
| ASTM D 664 : 2017 : REV A | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 7687 : 2023 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 892 : 2018 | Standard Test Method for Foaming Characteristics of Lubricating Oils |
| ASTM D 943 : 2019 | Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils |
| ASTM D 6971 : 2009 : R2014 | Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry |
| ASTM D 4175 : 2022 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7094 : 2017 : REV A | Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester |
| ASTM D 974 : 2022 | Standard Test Method for Acid and Base Number by Color-Indicator Titration |
| ASTM D 445 : 2021 : EDT 2 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 93 : 2019 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM F 312 : 2008 : R2016 | Standard Test Methods for Microscopical Sizing and Counting Particles from Aerospace Fluids on Membrane Filters |
| ASTM D 974 : 2021 | Standard Test Method for Acid and Base Number by Color-Indicator Titration |
| ASTM D 445 : 2017 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 6224 : 2023 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
| ASTM D 4175 : 2022 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2023 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7647 : 2010 : R2018 | Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction |
| ASTM D 7687 : 2021 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 7042 : 2021 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4175 : 2022 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 665 : 2023 | Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water |
| ASTM D 943 : 2018 | Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils |
| ASTM D 1500 : 2012 : R2017 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 445 : 2019 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 4175 : 2023 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2023 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2022 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 130 : 2018 | Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test |
| ASTM D 7094 : 2023 | Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester |
| ASTM D 664 : 2011 : REV A | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 892 : 2023 | Standard Test Method for Foaming Characteristics of Lubricating Oils |
| ASTM D 892 : 2018 : EDT 1 | Standard Test Method for Foaming Characteristics of Lubricating Oils |
| ASTM D 445 : 2018 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 665 : 2019 | Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water |
| ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 4898 : 2023 | Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis |
| ASTM D 2273 : 2008 : R2016 | Standard Test Method for Trace Sediment in Lubricating Oils (Withdrawn 2023) |
| ASTM D 445 : 2023 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 130 : 2012 | Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test |
| ASTM D 93 : 2018 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.