Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6461/D6461M : 2022

Current

Current

The latest, up-to-date edition.

Standard Specifications for Silt Fence Materials

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

07-01-2022

1.1This specification covers requirements and test methods for geotextile fabrics and associated components used in temporary silt fence applications. Table 1 is a material purchasing specification based on AASHTO M 288. Table 2 is a specification to be used in areas of high water flow. The specification in Table 2 is a higher strength, higher flow option than Table 1. Table 2 properties can withstand more hydraulic flow than the specification listed in Table 1. The Table 2 specification should be used in sensitive applications, such as areas near regulated waters and wetlands, but also areas that are prone to high flow runoff that require increased structural stability. The design professional has the option of Table 2 where the specifications listed in Table 1 are not sufficient to meet the demand of runoff.

1.2Both specifications are applicable to the use of a geotextile as a vertical permeable interceptor designed to remove suspended soil from overland, nonconcentrated water flow. The function of a temporary silt fence is to trap and allow settlement of soil particles from sediment-laden water. The purpose is to greatly limit the transport of eroded soil from construction sites and other areas affected by water runoff.

Note 1:It should be noted that proper installation and maintenance are critical for the effective functioning of silt fence.

1.3The tests used to characterize the silt fence are intended to ensure good workmanship and quality and are not necessarily adequate for design purposes in view of the wide variety of possible sediments and performance objectives.

1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

Note 2:Although the Table 1 specification should be acceptable in most erosion control applications, it should be noted that an alternative silt fence specification for a higher water flow rate, listed in Table 2, may be required by the engineers in areas that are susceptible to higher water runoff; using Table 2 specification will minimize safety hazards such as hydroplaning in these areas.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 35
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 6462 : 2019 Standard Practice for Silt Fence Installation and Maintenance

ASTM D 4533/D4533M : 2015 : R2023 Standard Test Method for Trapezoid Tearing Strength of Geotextiles
ASTM D 6637/D6637M : 2015 : R2023 Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
ASTM D 4533/D4533M : 2015 Standard Test Method for Trapezoid Tearing Strength of Geotextiles
ASTM D 6637/D6637M : 2015 Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
ASTM D 4632/D4632M : 2015 : REV A Standard Test Method for Grab Breaking Load and Elongation of Geotextiles
ASTM D 4491/D4491M : 2022 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 6241 : 2014 Standard Test Method for Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D 4491/D4491M : 2021 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 6241 : 2022 Standard Test Method for Static Puncture Index Strength of Geotextiles and Geotextile-Related Products Using a 50 mm Probe
ASTM D 6241 : 2022 : REV A Standard Test Method for Measuring Static Puncture Strength of Geotextiles and Geosynthetic-Related Products Using a 50 mm Probe
ASTM D 4632/D4632M : 2015 : REV A : R2023 Standard Test Method for Grab Breaking Load and Elongation of Geotextiles

View more information
$90.04
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more