ASTM F 2135 : 2001 : R2017 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings
Hardcopy , PDF
09-03-2022
English
12-04-2017
CONTAINED IN VOL. 08.04, 2018 Specifies standard fitting geometries for molded short-pattern plastic fittings intended for use in drain, waste, and vent applications.
1.1This specification covers standard fitting geometries for molded short-pattern plastic fittings intended for use in drain, waste, and vent applications.
1.2Fittings meeting the requirements of this specification are designed for use with outside-diameter controlled pipe. The body inside diameter can vary significantly as the wall thickness and outside diameter varies, and therefore, is not suitable for use as a fitting socket.
1.3Fittings meeting the requirements of this specification shall be tested in accordance with the applicable requirements of Specifications D2661 or D2665.
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
6
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 2618 : 2019 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
| ASTM D 2661 : 2014 : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 2390 : 2012 : R2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
| ASTM D 2665 : 2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 2618 : 2021 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
| ASTM F 2390 : 2021 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
| ASTM D 2661 : 2021 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2007 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2661 : 1978 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Drain, Waste, And Vent Pipe And Fittings |
| ASTM D 2665 : 2004 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2008 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2004 : REV A : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 1978 | Standard Specification for Poly(inyl Chloride) (PVC) Plastic Drain, Waste, And Vent Pipe And Fittings |
| ASTM D 2661 : 1997 : REV A : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 1991 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2009 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 2011 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2008 : REV B | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 1498 : 2008 | Standard Specification for Taper Pipe Threads 60<span class='unicode'>°</span> for Thermoplastic Pipe and Fittings |
| ASTM D 2749 : 2013 : REDLINE | Standard Symbols for Dimensions of Plastic Pipe Fittings (Withdrawn 2022) |
| ASTM D 2661 : 2000 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2002 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2665 : 2004 : REV A : EDT 2 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2749 : 2002 : R2008 | Standard Symbols for Dimensions of Plastic Pipe Fittings |
| ASTM D 2661 : 2002 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 1498 : 2008 : R2012 : EDT 1 | Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings |
| ASTM D 2661 : 2001 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2012 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 1991 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 2008 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2665 : 2002 : REV A : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2014 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2749 : 2002 | Standard Symbols for Dimensions of Plastic Pipe Fittings |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2665 : 2004 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2008 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1498 : 2000 | Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings |
| ASTM D 2749 : 1992 : R1999 : EDT 1 | Standard Symbols for Dimensions of Plastic Pipe Fittings |
| ASTM D 2665 : 2000 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2001 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 2014 : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 2014 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2749 : 2013 | Standard Symbols for Dimensions of Plastic Pipe Fittings (Withdrawn 2022) |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2665 : 2002 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2010 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2665 : 2011 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 2021 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2661 : 2006 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.