We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN ISO 10535:2006

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    HOISTS FOR THE TRANSFER OF DISABLED PERSONS - REQUIREMENTS AND TEST METHODS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2006

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements and test methods
       4.1 General requirements
       4.2 General test methods
       4.3 Safety requirements
       4.4 Requirements for body-support units
       4.5 Central suspension point
       4.6 Spreader bar
       4.7 Performance
       4.8 Rate (velocity) of lifting and lowering
       4.9 Operating forces/torques
       4.10 Durability
       4.11 Hydraulic components
       4.12 Pneumatic components
       4.13 Information supplied by the manufacturer
    5 Mobile hoists - Specific requirements and test methods
       5.1 General requirements
       5.2 Static strength
       5.3 Static stability
       5.4 Immobilizing device (brakes)
       5.5 Moving forces
       5.6 Instructions for use
    6 Standing and/or raising hoists - Specific requirements
       and test methods
       6.1 General requirements
       6.2 Static strength
       6.3 Static stability
       6.4 Immobilizing device (brakes)
       6.5 Moving forces
       6.6 Durability
       6.7 Instructions for use
    7 Stationary hoists - Specific requirements and test
       methods
       7.1 General requirements
       7.2 Specific safety requirements
       7.3 Static strength (free-standing stationary hoists
             only)
       7.4 Static stability (free-standing stationary hoists
             only)
       7.5 Static strength for all other stationary hoists
       7.6 Instructions for use
    8 Non-rigid body-support units - Specific requirements
       and test methods
       8.1 General requirements
       8.2 Requirements for material and seams of the non-rigid
             body-support unit
       8.3 Test methods for non-rigid body-support unit
       8.4 Information supplied by the manufacturer
    9 Rigid body-support units - Specific requirements and
       test methods
       9.1 General requirements
       9.2 Requirements for backrest
       9.3 Requirements and test methods for durability
       9.4 Information supplied by the manufacturer
    10 Bathtub hoists - Specific requirements and test methods
       10.1 General requirements
       10.2 General test methods
       10.3 Safety requirements
       10.4 Body-support units
       10.5 Spreader bar
       10.6 Performance
       10.7 Rate (velocity) of lifting and lowering
       10.8 Operating forces
       10.9 Durability
       10.10 Static strength and stability
       10.11 Hydraulic components
       10.12 Pneumatic components
       10.13 Specific safety requirements
       10.14 Non-rigid body-support units
       10.15 Rigid body-support units - Requirements
       10.16 Information supplied by the manufacturer
    Annex A (informative) Structure of ISO 10535
    Annex B (informative) Periodic inspection
    Annex ZA (informative) Clauses of this EN addressing essential
                           requirements or other provisions of EU
                           Directives

    Abstract - (Show below) - (Hide below)

    Defines requirements and test methods only for hoists and body-support units intended for the transfer of disabled persons as classified in ISO 9999:2002: - 12 36 03 Mobile hoists with sling seats; - 12 36 04 Standing mobile hoists; - 12 36 06 Mobile hoists with solid seats; - 12 36 09 Hoist trolleys; - 12 36 12 Stationary hoists fixed to the wall/walls, floor and/or ceiling; - 12 36 15 Stationary hoists fixed to, mounted in or on another product; - 12 36 18 Stationary free-standing hoists; - 12 36 21 Body-support units for hoists.

    General Product Information - (Show below) - (Hide below)

    Committee CH/173/-/6
    Development Note Supersedes 95/563244 DC (08/2004) Supersedes 04/30081057 DC. (01/2007) Reviewed and confirmed by BSI, September 2015. (09/2015)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    17/30335834 DC : 0 BS 8300-2 - DESIGN OF AN ACCESSIBLE AND INCLUSIVE BUILT ENVIRONMENT - PART 2: BUILDINGS - CODE OF PRACTICE

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 854:2015 RUBBER HOSES AND HOSE ASSEMBLIES - TEXTILE REINFORCED HYDRAULIC TYPE - SPECIFICATION
    IEC 60601-1:2005+AMD1:2012 CSV Medical electrical equipment - Part 1: General requirements for basic safety and essential performance
    EN 1021-1:2014 FURNITURE - ASSESSMENT OF THE IGNITABILITY OF UPHOLSTERED FURNITURE - PART 1: IGNITION SOURCE SMOULDERING CIGARETTE
    ISO 3758:2012 Textiles Care labelling code using symbols
    ISO 14253-1:2017 Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for verifying conformity or nonconformity with specifications
    EN 614-1:2006+A1:2009 SAFETY OF MACHINERY - ERGONOMIC DESIGN PRINCIPLES - PART 1: TERMINOLOGY AND GENERAL PRINCIPLES
    EN 12182:2012 Assistive products for persons with disability - General requirements and test methods
    IEC 60601-1-2:2014 Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests
    EN 13480-3:2017 (edition 2) Metallic industrial piping - Part 3: Design and calculation
    ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
    ISO 10993-1:2009 Biological evaluation of medical devices Part 1: Evaluation and testing within a risk management process
    IEC 61000-3-3 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION
    ISO 9999:2016 Assistive products for persons with disability Classification and terminology
    ISO 14971:2007 Medical devices Application of risk management to medical devices
    EN 853:2015 RUBBER HOSES AND HOSE ASSEMBLIES - WIRE BRAID REINFORCED HYDRAULIC TYPE - SPECIFICATION
    EN 980 : 2008 SYMBOLS FOR USE IN THE LABELLING OF MEDICAL DEVICES
    EN 1021-2:2014 FURNITURE - ASSESSMENT OF THE IGNITABILITY OF UPHOLSTERED FURNITURE - PART 2: IGNITION SOURCE MATCH FLAME EQUIVALENT
    IEC 61000-3-2 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective