EN ISO 3126:2005
|
Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
|
EN 1555-1:2010
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
|
EN 682:2002/A1:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
|
EN 10226-2:2005
|
Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
|
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
|
ISO 10838-3:2001
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
EN ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
|
ISO 10838-2:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
|
EN ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
|
ISO 10838-1:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
|
IEC 60364-1:2005
|
Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
|
EN 1716:1997
|
Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee
|
CEN/TR 15438:2007
|
Plastics piping systems - Guidance for coding of products and their intended uses
|
EN ISO 228-1:2003
|
Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
|
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions
|
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
|
HD 60364-1:2008/A11:2017
|
LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 1: FUNDAMENTAL PRINCIPLES, ASSESSMENT OF GENERAL CHARACTERISTICS, DEFINITIONS
|
EN ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
PREN 1555-4 : DRAFT 2008
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES
|
ISO 13955:1997
|
Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
|
EN 1555-5:2010
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
|
EN 12007-2:2012
|
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar)
|
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
|
EN 1555-2:2010
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
|
EN 60335-1:2012/A13:2017
|
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
|
CEN/TS 1555-7:2013
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
|
EN ISO 1133:2005
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
|
ISO 13950:2007
|
Plastics pipes and fittings Automatic recognition systems for electrofusion joints
|
EN 12117:1997
|
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
|
EN 10226-1:2004
|
Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
|
ISO 1133:2005
|
Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
|
ISO 13951:2015
|
Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
|
ISO 228-1:2000
|
Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
|
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
|