Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-103: Keying and alignment pin

Published date

17-09-2004

Publisher

European Committee for Standards - Electrical

FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Terms and definitions
4 Arrangement overview: Keying of plug-in units in a subrack
  4.1 General
  4.2 Subrack interface dimensions for keying
  4.3 Plug-in unit keying interface dimensions
  4.4 Key dimensions
  4.5 Programming of keys
  4.6 Keying chamber inspection dimensions
5 Arrangement overview: alignment and/or electrical contact
  of a plug-in unit to a subrack
  5.1 General
  5.2 Alignment and/or electrical contact receptacle in the
      subrack guide rail for printed board type plug-in units
      (width dimension >= 4 x 5,08 mm)
  5.3 Alignment and/or electrical contact interface
      inspection dimensions
6 Arrangement overview: Subrack guide rail and printed board,
  2,54 mm offset of the printed board reference plane
  6.1 General
  6.2 Dimensions of the subrack guide rail with 2,54 mm offset
      of the printed board reference plane
  6.3 Reference plane for printed boards with 2,54 mm offset
      position
7 Dimensions used in the figures
Annex ZA (normative) Normative references to international
                     publications with their corresponding
                     European publications

Covers only the additional interface dimensions for an alignment pin and a keying device used with subracks and plug-in units according to EN 60297-3-101. May also be used in conjunction with EN 60297-3-102.

Committee	CLC/SR 48D
DevelopmentNote	Supersedes EN 60297-5-104 and EN 60297-5-105. (09/2004) Supersedes UNE EN 60297-5-104 & UNE EN 60297-5-105. (09/2007) Supersedes CEI EN 60297-5-104 and CEI EN 60297-5-105. (05/2008)
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Current
Supersedes	EN 60297-5-104:2001 UNE-EN 60297-5-104:2001 EN 60297-5-105:2001 UNE-EN 60297-5-105:2001

Standards	Relationship
NF EN 60297-3-103 : 2005	Identical
BS EN 60297-3-103:2004	Identical
NEN EN IEC 60297-3-103 : 2004	Identical
NBN EN 60297-3-103 : 2006	Identical
IEC 60297-3-103:2004	Identical
PN EN 60297-3-103 : 2005	Identical
CEI EN 60297-3-103 : 2005	Identical
I.S. EN 60297-3-103:2004	Identical
DIN EN 60297-3-103:2005-06	Identical
UNE-EN 60297-3-103:2004	Identical

IEC 60297-3-101:2004	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units
EN 60297-3-102:2004	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-102: Injector/extractor handle
EN 60297-3-101:2004	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units
IEC 60297-3-102:2004	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-102: Injector/extractor handle
IEC 60917-1:1998+AMD1:2000 CSV	Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard