HEAT SHRINKABLE MOULDED SHAPES - PART 1: DEFINITIONS AND GENERAL REQUIREMENTS

Published date

15-12-2006

Publisher

European Committee for Standards - Electrical

Foreword
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Specimens
5 Classification
6 Ordering
7 Dimensions
8 Colour
9 Finish
10 Packaging
11 Labelling
12 Qualification approval requirements
13 Consignment tests
Annex A (informative) Heat shrinkable moulded shapes
                      (typical configuration after
                      recovery)
Annex ZA (normative) Normative references to international
                     publications with their corresponding
                     European publications
Bibliography

This standard is applicable to heat shrinkable moulded shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection and strain relief for connector/cable terminations and multi-way transitions.

Committee	SR 15
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Current

Standards	Relationship
SN EN 62329-1 : 2006	Identical
PN EN 62329-1 : 2006 AC 2007	Identical
IEC 62329-1:2005	Identical
UNE-EN 62329-1:2006	Identical
CEI EN 62329-1 : 2006	Identical
I.S. EN 62329-1:2006&AC:2006	Identical
BS EN 62329-1:2006	Identical
VDE 0342-1 : 2006 COR 1 2007	Identical
NF EN 62329-1 : 2006	Identical
NBN EN 62329-1 : 2006	Identical
DIN EN 62329-1 : 2006 COR 1 2007	Identical
NEN EN IEC 62329-1 : 2006 C11 2007	Identical

I.S. EN 62329-2:2006	HEAT SHRINKABLE MOULDED SHAPES - PART 2: METHODS OF TEST
EN 62329-3-100 : 2010	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 100: HEAT-SHRINKABLE MOULDED SHAPE DIMENSIONS
EN 62329-3-101 : 2010	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 101: HEAT-SHRINKABLE MOULDED SHAPES, POLYOLEFIN, SEMI-RIGID, LIMITED FIRE HAZARD, MATERIAL REQUIREMENTS AND SYSTEM PERFORMANCE
CEI EN 62329-3-101 : 2012	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 101: HEAT-SHRINKABLE MOULDED SHAPES, POLYOLEFIN, SEMI-RIGID, LIMITED FIRE HAZARD, MATERIAL REQUIREMENTS AND SYSTEM PERFORMANCE
I.S. EN 62329-3-101:2010	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 101: HEAT-SHRINKABLE MOULDED SHAPES, POLYOLEFIN, SEMI-RIGID, LIMITED FIRE HAZARD, MATERIAL REQUIREMENTS AND SYSTEM PERFORMANCE
I.S. EN 62329-3-100:2010	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 100: HEAT-SHRINKABLE MOULDED SHAPE DIMENSIONS
CEI EN 62329-3-102 : 2012	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 102: HEAT-SHRINKABLE ELASTOMERIC MOULDED SHAPES, SEMI-RIGID, MATERIAL REQUIREMENTS AND SYSTEM PERFORMANCE
BS EN 62329-3-100:2010	Heat-shrinkable moulded shapes Specification requirements for shape dimensions, material requirements and compatibility performance. Heat-shrinkable moulded shape dimensions
BS EN 62329-2:2006	Heat shrinkable moulded shapes Methods of test
BS EN 62329-3-101:2010	Heat-shrinkable moulded shapes Specification requirements for shape dimensions, material requirements and compatibility performance. Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance
BS EN 62329-3-102:2010	Heat-shrinkable moulded shapes Specification requirements for shape dimensions, material requirements and compatibility performance. Heat-shrinkable elastomeric moulded shapes, semi-rigid, material requirements and system performance
CEI EN 62329-3-100 : 2012	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 100: HEAT-SHRINKABLE MOULDED SHAPE DIMENSIONS
I.S. EN 62329-3-102:2010	HEAT-SHRINKABLE MOULDED SHAPES - PART 3: SPECIFICATION REQUIREMENTS FOR SHAPE DIMENSIONS, MATERIAL REQUIREMENTS AND COMPATIBILITY PERFORMANCE - SHEET 102: HEAT-SHRINKABLE ELASTOMERIC MOULDED SHAPES, SEMI-RIGID, MATERIAL REQUIREMENTS AND SYSTEM PERFORMANCE
EN 62329-3-102:2010	Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 102: Heat-shrinkable elastomeric moulded shapes, semi-rigid, material requirements and system performance
EN 62329-2:2006	Heat shrinkable moulded shapes - Part 2: Methods of test

IEC 60050-212:2010	International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases
EN 62329-2:2006	Heat shrinkable moulded shapes - Part 2: Methods of test
IEC 62329-2:2006	Heat-shrinkable moulded shapes - Part 2: Methods of test

View more information

Sorry this product is not available in your region.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

EN 62329-1:2006/corrigendum:2006

HEAT SHRINKABLE MOULDED SHAPES - PART 1: DEFINITIONS AND GENERAL REQUIREMENTS

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory