We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN 60068-2-27:2009

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Description of test apparatus
    5 Severities
    6 Preconditioning
    7 Initial measurements and functional performance test
    8 Testing
    9 Recovery
    10 Final measurements
    11 Information to be given in the relevant specification
    12 Information to be given in the test report
    Annex A (normative) - Selection and application of pulse
            shapes - Guidance
    Annex B (informative) - Shock response spectra and other
            characteristics of pulse shapes
    Annex C (informative) - Comparison between impact tests
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Describes a standard procedure for determining the ability of a specimen to withstand specified severities of non-repetitive or repetitive shocks.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 60068-2-29. (09/2011) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    EN 60721-3-1:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STORAGE
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60068-2-81:2003 Environmental testing - Part 2-81: Tests - Test Ei: Shock - Shock response spectrum synthesis
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    EN 60721-3-5 : 1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - SECTION 5: GROUND VEHICLE INSTALLATIONS
    IEC 60721-3-5:1997 Classification of environmental conditions - Part 3: Classificationof groups of environmental parameters and their severities -Section 5: Ground vehicle installations
    IEC 60068-2-31:2008 ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS
    ISO 2041:2009 Mechanical vibration, shock and condition monitoring Vocabulary
    IEC 60068-2-47:2005 Environmental testing - Part 2-47: Test - Mounting of specimens for vibration, impact and similar dynamic tests
    EN 60068-2-55:2013 Environmental testing - Part 2-55: Tests - Test Ee and guidance - Loose cargo testing including bounce
    IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
    ISO 8568:2007 Mechanical shock Testing machines Characteristics and performance
    IEC 60068-2-55:2013 Environmental testing - Part 2-55: Tests - Test Ee and guidance - Loose cargo testing including bounce
    IEC 60721-3-1:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3-1: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STORAGE
    EN 60068-2-47:2005 ENVIRONMENTAL TESTING - PART 2-47: TESTS - MOUNTING OF SPECIMENS FOR VIBRATION, IMPACT AND SIMILAR DYNAMIC TESTS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective