Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • ISO 21004:2006

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Plastics piping systems Multilayer pipes and their joints, based on thermoplastics, for water supply

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English

    Published date:  25-10-2006

    Publisher:  International Organization for Standardization

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 21004:2006 specifies the general requirements and the performance requirements for multilayer pipes based on thermoplastics intended to be used for water supply outside buildings, for buried water mains and services and for water supplies above ground.

    ISO 21004:2006 gives guidance for the design of piping systems consisting of multilayer pipes based on thermoplastics or, for which at least 60 % of the wall thickness is polymeric material, and the inner layer in contact with water is made of polymeric material.

    The polymeric layers used for the stress-bearing layers are selected from polybutylene (PB), polyethylene (PE), crosslinked polyethylene (PE-X), polypropylene (PP), chlorinated poly(vinyl chloride) (PVC-C) and unplasticized poly(vinyl chloride) (PVC-U).

    ISO 21004:2006 is applicable to piping systems used for the conveyance under pressure of cold water (up to approximately 20 C) for drinking. It is also applicable to piping systems for the conveyance of water (up to and including 40 C) for general purposes.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes ISO/DIS 21004 (10/2006)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS ISO 4427-2 : 2007 PLASTICS PIPING SYSTEMS - POLYETHYLENE (PE) PIPES AND FITTINGS FOR WATER SUPPLY - PART 2: PIPES
    UNI EN 15014 : 2008 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
    11/30239906 DC : 0 BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER AND OTHER LIQUIDS UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
    BS ISO 17885:2015 Plastics piping systems. Mechanical fittings for pressure piping systems. Specifications
    DIN EN 15014:2014-06 (Draft) PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
    BS EN 15014:2007 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
    EN 12201-2:2011+A1:2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
    PREN 15014 : DRAFT 2014 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
    ISO 17885:2015 Plastics piping systems Mechanical fittings for pressure piping systems Specifications
    I.S. EN 12201-2:2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
    DIN EN 15014:2008-01 Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints
    I.S. EN 15014:2007 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
    BS EN 12201-2 : 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
    UNI EN 12201-2 : 2013 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
    10/30212147 DC : 0 BS EN 12201-2 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
    UNE-EN 12201-2:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
    DIN EN 15014 E : 2008 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
    EN 15014:2007 Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints
    ISO 4427-2:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes
    14/30297465 DC : 0 BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
    DIN EN 12201-2:2013-12 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes (includes Amendment A1:2013)

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6259-2:1997 Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI)
    ISO 13846:2000 Plastics piping systems End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping Test method for long-term leaktightness under internal water pressure
    ISO 3213:2009 Polypropylene (PP) pipes Effect of time and temperature on the expected strength
    ISO 4422-3:1996 Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 3: Fittings and joints
    ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 4427-3:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings
    ISO 15874-3:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings
    ISO 15877-3:2009 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 10146:1997 Crosslinked polyethylene (PE-X) pipes Effect of time and temperature on the expected strength
    ISO 4427-1:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General
    ISO 15875-5:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system
    ISO 13968:2008 Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility
    ISO 15874-1:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General
    ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
    ISO 3501:2015 Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal force
    ISO 4422-1:1996 Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 1: General
    ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    ISO 17456:2006 Plastics piping systems Multilayer pipes Determination of long-term strength
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 3459:2015 Plastic piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under negative pressure
    ISO 4427-5:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system
    ISO 15877-2:2009 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 2: Pipes
    ISO 22391-5:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system
    ISO 15875-2:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes
    ISO 12230:2012 Polybutene-1 (PB-1) pipes — Effect of time and temperature on the expected strength
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
    ISO 15877-1:2009 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 1: General
    ISO 15874-2:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    ISO 15876-1:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 161-2:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 2: Inch-based series
    ISO 15876-3:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings
    ISO 15877-5:2009 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system
    ISO 22391-2:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes
    ISO 13783:1997 Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure
    ISO 13844:2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes Test method for leaktightness under negative pressure, angular deflection and deformation
    ISO 16871:2003 Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering
    ISO 472:2013 Plastics Vocabulary
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 24033:2009 Polyethylene of raised temperature resistance (PE-RT) pipes Effect of time and temperature on the expected strength
    ISO 4422-2:1996 Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 2: Pipes (with or without integral sockets)
    ISO 4422-4:1997 Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 4: Valves and ancillary equipment
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 15876-2:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes
    ISO 15875-1:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 1: General
    ISO 4422-5:1997 Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 5: Fitness for purpose of the system
    ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
    ISO 22391-3:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings
    ISO 13761:2017 Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C
    ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
    ISO 15875-3:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings
    ISO 22391-1:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General
    ISO 17454:2006 Plastics piping systems Multilayer pipes Test method for the adhesion of the different layers using a pulling rig
    ISO 15874-5:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system
    ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
    ISO 15876-5:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 3503:2015 Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    ISO 4427-2:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes
    ISO 13845:2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pressure and with angular deflection
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more