Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • NACE 12 : 2003

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-06-2019

    Language(s):  English

    Published date:  01-01-2003

    Publisher:  National Association of Corrosion Engineers

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. Introduction
    2. Definitions
    3. Summary of Practice
    4. TSC Feedstock Requirements
    5. Surface Preparation Requirements
    6. Thermal Spray Equipment Setup
    7. Job Reference Standard (JRS)
    8. TSC Application Procedure
    9. Inspection of Applied TSC
    10. Application of Optional Sealers and Topic
    11. Records
    12. Debris Containment and Control
    13. Work Procedures and Safety
    14. Application Procedure
    References
    Bibliography
    Appendix A: Example Images of Electrochemical Sensors (Nonmandatory)
    Appendix B: Example of Reporting Information (Nonmandatory)
    Appendix C: Commentary (Nonmandatory)
    Appendix D: Example of Reporting Information (Nonmandatory)

    Abstract - (Show below) - (Hide below)

    Describes procedure for the application of metallic thermal spray coating (TSCs) of aluminum, zinc, and their alloys and composites for the corrosion protection of steel.

    General Product Information - (Show below) - (Hide below)

    Committee STG 02
    Development Note Jointly published by NACE, AWS and SSPC. Also numbered as AWS C2.23M/C2.23 & SSPC-CS 23.00. (09/2016)
    Document Type Standard
    Publisher National Association of Corrosion Engineers
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    NACE SP 01 08 : 2008 CORROSION CONTROL OF OFFSHORE STRUCTURES BY PROTECTIVE COATINGS
    NACE 30105 : 0 ELECTRICAL ISOLATION/CONTINUITY AND COATING ISSUES FOR OFFSHORE PIPELINE CATHODIC PROTECTION SYSTEMS

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 5493:1977 Code of practice for protective coating of iron and steel structures against corrosion
    NACE WJ 3 : 2012 WATERJET CLEANING OF METALS - THOROUGH CLEANING
    ASTM B 833 : 2013 : REDLINE Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
    NFPA 58 : 2017 LIQUEFIED PETROLEUM GAS CODE
    NACE SP 01 78 : 2007 DESIGN, FABRICATION, AND SURFACE FINISH PRACTICES FOR TANKS AND VESSELS TO BE LINED FOR IMMERSION SERVICE
    NACE WJ 2 : 2012 WATERJET CLEANING OF METALS - VERY THOROUGH CLEANING
    ASTM D 4541 : 2017 : REDLINE Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
    ASTM D 4417 : 2014 : REDLINE Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
    SSPC-SP WJ 4 : 2012 WATERJET CLEANING OF METALS - LIGHT CLEANING
    SSPC-SP 10 : 2015 NEAR-WHITE BLAST CLEANING
    ASTM D 4285 : 1983 : R2018 Standard Test Method for Indicating Oil or Water in Compressed Air
    SSPC-SP WJ 2 : 2012 WATERJET CLEANING OF METALS - VERY THOROUGH CLEANING
    NACE WJ 1 : 2012 WATERJET CLEANING OF METALS - CLEAN TO BARE SUBSTRATE
    AWS C2.14 : 1974 CORROSION TESTS OF FLAME SPRAYED COATED STEEL, 19-YEAR REPORT,
    SSPC-SP WJ 1 : 2012 WATERJET CLEANING OF METALS - CLEAN TO BARE SUBSTRATE
    SSPC-SP WJ 3 : 2012 WATERJET CLEANING OF METALS - THOROUGH CLEANING
    SSPC-GUIDE 15 : 2013 FIELD METHODS FOR EXTRACTION AND ANALYSIS OF SOLUBLE SALTS ON STEEL AND OTHER NONPOROUS SUBSTRATES
    SSPC-PA 17 : 2012 PROCEDURE FOR DETERMINING CONFORMANCE TO STEEL PROFILE/SURFACE ROUGHNESS/PEAK COUNT REQUIREMENTS
    SSPC-AB 1 : 2015 MINERAL AND SLAG ABRASIVES
    AWS C2.25/C2.25M : 2012 SPECIFICATION FOR THERMAL SPRAY FEEDSTOCK - WIRE AND RODS
    ASTM E 337 : 2015 : REDLINE Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
    NACE WJ 4 : 2012 WATERJET CLEANING OF METALS - LIGHT CLEANING
    SSPC-AB 2 : 2015 CLEANLINESS OF RECYCLED FERROUS METALLIC ABRASIVES
    CFR 29(PTS1911-1919) : 1984 LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR
    ANSI Z49.1 : 2012 SAFETY IN WELDING, CUTTING, AND ALLIED PROCESSES
    SSPC-SP 5 : 2015 WHITE METAL BLAST CLEANING
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more