SN EN 50132-2-1 : 1997

Committees responsible<br>Foreword<br>Introduction<br>1 Scope<br>2 Normative references and bibliography<br>&nbsp;&nbsp;&nbsp;&nbsp;2.1 Normative references<br>&nbsp;&nbsp;&nbsp;&nbsp;2.2 Bibliography<br>3 Definitions and abbreviations<br>&nbsp;&nbsp;&nbsp;&nbsp;3.1 Definitions<br>&nbsp;&nbsp;&nbsp;&nbsp;3.2 Abbreviations<br>4 Requirements<br>&nbsp;&nbsp;&nbsp;&nbsp;4.1 Requirements<br>&nbsp;&nbsp;&nbsp;&nbsp;4.2 Video signal output<br>&nbsp;&nbsp;&nbsp;&nbsp;4.3 Automatic gain control (AGC)<br>&nbsp;&nbsp;&nbsp;&nbsp;4.4 Gamma correction<br>&nbsp;&nbsp;&nbsp;&nbsp;4.5 Sensitivity and signal to noise ratio<br>&nbsp;&nbsp;&nbsp;&nbsp;4.6 Limiting resolution<br>&nbsp;&nbsp;&nbsp;&nbsp;4.7 Contrast Transfer Function (CTF)<br>&nbsp;&nbsp;&nbsp;&nbsp;4.8 Black level<br>&nbsp;&nbsp;&nbsp;&nbsp;4.9 Automatic light control (ALC) range<br>&nbsp;&nbsp;&nbsp;&nbsp;4.10 Synchronization<br>&nbsp;&nbsp;&nbsp;&nbsp;4.11 Geometric distortion<br>&nbsp;&nbsp;&nbsp;&nbsp;4.12 Aspect ratio<br>&nbsp;&nbsp;&nbsp;&nbsp;4.13 Power supply<br>&nbsp;&nbsp;&nbsp;&nbsp;4.14 Electrical safety<br>&nbsp;&nbsp;&nbsp;&nbsp;4.15 Camera lens mount<br>&nbsp;&nbsp;&nbsp;&nbsp;4.16 Camera mount<br>&nbsp;&nbsp;&nbsp;&nbsp;4.17 Electromagnetic compatibility<br>&nbsp;&nbsp;&nbsp;&nbsp;4.18 Environmental conditions<br>5 Test conditions<br>&nbsp;&nbsp;&nbsp;&nbsp;5.1 Introduction<br>&nbsp;&nbsp;&nbsp;&nbsp;5.2 Test equipment<br>&nbsp;&nbsp;&nbsp;&nbsp;5.3 Laboratory conditions<br>6 Performance tests<br>&nbsp;&nbsp;&nbsp;&nbsp;6.1 Video signal output<br>&nbsp;&nbsp;&nbsp;&nbsp;6.2 Gamma correction<br>&nbsp;&nbsp;&nbsp;&nbsp;6.3 Sensitivity<br>&nbsp;&nbsp;&nbsp;&nbsp;6.4 Signal to noise ratio<br>&nbsp;&nbsp;&nbsp;&nbsp;6.5 Limiting resolution<br>&nbsp;&nbsp;&nbsp;&nbsp;6.6 Automatic gain control<br>&nbsp;&nbsp;&nbsp;&nbsp;6.7 Contrast transfer function (CTF)<br>&nbsp;&nbsp;&nbsp;&nbsp;6.8 Black level<br>&nbsp;&nbsp;&nbsp;&nbsp;6.9 Synchronization<br>&nbsp;&nbsp;&nbsp;&nbsp;6.10 Geometric distortion<br>7 Environmental testing<br>&nbsp;&nbsp;&nbsp;&nbsp;7.1 Introduction<br>&nbsp;&nbsp;&nbsp;&nbsp;7.2 Selection of severity of tests<br>&nbsp;&nbsp;&nbsp;&nbsp;7.3 Dry heat (operational)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.4 Dry heat (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.5 Cold (operational)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.6 Damp heat, steady state (operational)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.7 Damp heat, steady state (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.8 Damp heat, cyclic (operational)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.9 Damp heat, cyclic (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.10 Water (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.11 Sulfur dioxide (SO2) corrosion (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.12 Salt mist, cyclic (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.13 Shock (operational)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.14 Vibration, sinusoidal (operational)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.15 Vibration, sinusoidal (endurance)<br>&nbsp;&nbsp;&nbsp;&nbsp;7.16 Dust tightness (endurance)<br>8 Documentation<br>9 Marking and labelling<br>Annexes<br>A (informative) Scene illumination in relation to camera<br>&nbsp;&nbsp;&nbsp;&nbsp;sensitivity<br>B (normative) CCTV test charts