AS 1341-1982

1 - AS 1341-1982 INFORMATION PROCESSING UNPPUNCHED PAPER TAPE
4 - PREFACE
4 - CONTENTS
5 - 1 SCOPE.
5 - 2 TEST CONDITIONS AND METHODS OF TEST
5 - 2.1 Sampling.
5 - 2.2 Test Conditions.
5 - 2.3 Conditioning of Test Samples.
5 - 2.4 Methods of Test.
5 - 3 DIMENSIONS
5 - 3.1 Width.
5 - 3.2 Thickness.
5 - 4 CHEMICAL PROPERTIES.
5 - 4.1 Hydrogen Ion Concentration.
5 - 4.2 Ash Content.
5 - 4.3 Grit Content.
5 - 4.4 Composition and Quality.
5 - 4.5 Chloride Content.
5 - 4.6 Sulphate Content.
5 - 4.7 Lubricating Additives.
5 - 5 PHYSICAL PROPERTIES.
5 - 5.1 Paper Grammage.
5 - 5.2 Strength.
5 - 5.2.1 Static tensile strength.
5 - 5.2.2 Internal tear resistance.
6 - 5.3 Dimensional Stability.
6 - 5.4 Folding Endurance.
6 - 5.5 Optical Properties.
6 - 5.6 Electrical Properties.
6 - 5.6.1 Bulk conductivity.
6 - 5.6.2 Surface resistivity limits.
6 - 5.7 Printability.
6 - 5.8 Colour.
6 - 5.9 Pre-printing.
6 - 5.10 Quality.
6 - 6 COILING OF UNPUNCHED TAPE.
6 - 6.1 Inner Diameter.
6 - 6.2 Outer Diameter.
6 - 6.3 End of Paper Tape Marker.
6 - 6.3.1 Warning mark.
6 - 6.3.2 Length of mark.
6 - 6.3.3 Colouring matter.
6 - 6.4 Pull-off Force.
6 - 6.5 Surface Finish.
6 - 6.6 Tightness of Coiling.
6 - 6.7 Length of Tape.
7 - APPENDIX A - METHOD FOR THE CONDITIONING OF PAPER TEST SAMPLES
7 - A1 SCOPE.
7 - A2 DEFINITIONS.
7 - A2.1 Relative Humidity (r.h.).
7 - A2.2 Conditioning.
7 - A3 PRINCIPLE.
7 - A4 CONDITIONING ATMOSPHERE.
7 - A5 EQUIPMENT.
7 - A5.1 Room and Measuring Instrumentation.
7 - A5.2 Determination of Temperature and Relative Humidity.
7 - A6 PROCEDURE.
7 - A6.1 Preliminary Treatment of Sampl es.
7 - A6.2 Conditioning.
7 - A7 TEST REPORT.
8 - APPENDIX B - DIMENSIONS
8 - B1 MEASUREMENT OF WIDTH.
8 - B2 MEASUREMENTOFTHICKNESS.
8 - B2.1 General.
8 - B2.2 Dial Micrometer Characteristics.
8 - B2.3 Calibration.
8 - B2.4 Sampling.
8 - B2.5 Test Procedure.
8 - B2.6 Results.
9 - APPENDIX C - DETERMINATION OF ASH
9 - C1 DEFINITION.
9 - C2 APPARATUS.
9 - C3 SAMPLING.
9 - C4 PREPARATION OF TEST PIECE.
9 - C5 PROCEDURE.
9 - C6 EXPRESSION OF RESULTS.
10 - APPENDIX D - DETERMINATION OF GRIT CONTENT
10 - D1 GENERAL.
10 - D2 DETERMINATION OF ABRASIVE GRIT.
10 - APPENDIX E - DETERMINATIONOFOILCONTENT
11 - APPENDIX F - DETERMINATION OF DIMENSIONAL STABILITY
11 - F1 SCOPE.
11 - F2 TEST ATMOSPHERE.
11 - F2.1 Test Temperature.
11 - F2.2 Length Measurements.
11 - F2.3 Atmospheric Conditions of Testing.
11 - F3 TEST PARAMETERS.
11 - F4 TEST REPORT.
12 - APPENDIX G - DETERMINATION OF LIGHT TRANSMISSION AND NOISE FACTOR
12 - G1 INTRODUCTION.
12 - G2 APPARATUS.
12 - G2.1 General.
12 - G2.2 The Light Source.
12 - G2.3 The Optical Path.
12 - G2.4 The Paper.
12 - G2.5 The Photocell.
12 - G2.6 The Measuring Meter.
12 - G3 THE LIGHT-COLLECTING ELEMENTS.
12 - G4 TEST PROCEDURE AND CALCULATIONS.
14 - APPENDIX H - DETERMINATION OF SURFACE RESISTIVITY
14 - H1 PREPARATION OF TEST PIECES FOR MEASUREMENT.
14 - H2 MEASUREMENT OF SURFACE RESISTIVITY.
14 - H3 PRESENTATION OF RESULTS.
14 - APPENDIX J - APPLICATION OF STANDARD BY THE AUSTRALIAN DEPARTMENT OF DEFENCE
14 - J1 APPROVED ITEM NAME (AIN).
14 - J2 ENDORSEMENT.
14 - J3 APPLICABLE DOCUMENTS.
14 - J4 VARIATIONS FROM THE AUSTRALIAN STANDARD.
14 - J5 ORDERING DATA.