Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
ASTM
ASTM A 213/A213M : 2011 : REV A

ASTM A 213/A213M : 2011 : REV A

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

01-10-2011

Publisher

American Society for Testing and Materials

1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2.

1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.

1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

TABLE 1 Chemical Composition Limits, %A, for Low Alloy Steel

GradeUNS DesignationComposition, %
Carbon Manga-
nese 		Phospho-
rus		Sul-
fur 		Silicon
NickelChromiumMolybdenumVana-
dium		BoronNiobiumNitrogenAluminumTungstenOther Elements
T2K115470.10–0.20 0.30–0.610.025 0.025B 0.10–0.30...0.50–0.810.44–0.65 .....................
T5K41545 0.150.30–0.600.025 0.0250.50 ...4.00–6.000.45–0.65.....................
T5bK51545 0.150.30–0.600.025 0.0251.00–2.00...4.00–6.000.45–0.65.....................
T5cK41245 0.120.30–0.600.025 0.0250.50 ...4.00–6.000.45–0.65..................Ti 4xC–0.70
T9K90941 0.150.30–0.600.025 0.0250.25–1.00...8.00–10.000.90–1.10.....................
T11K11597 0.05–0.15 0.30–0.600.025 0.0250.50–1.00... 1.00–1.500.44–0.65.....................
T12K115620.05–0.150.30–0.61 0.025 0.025B0.50 ... 0.80–1.250.44–0.65 .....................
T17K12047 0.15–0.25 0.30–0.610.025 0.0250.15–0.35... 0.80–1.25...0.15..................
T21K31545 0.05–0.15 0.30–0.600.025 0.0250.50–1.00... 2.65–3.350.80–1.06.....................
T22K21590 0.05–0.15 0.30–0.600.025 0.025 0.50... 1.90–2.600.87–1.13.....................
T23K407120.04–0.100.10–0.600.0300.0100.50 0.40 1.90–2.600.05–0.300.20–0.300.0010–
0.006		0.02–0.080.0150.0301.45–1.75Ti 0.005–0.060
Ti/N ≥ 3.5C
T24K307360.05–0.100.30–0.700.0200.0100.15–0.45...2.20–2.600.90–1.100.20–0.300.0015–
0.007		...0.0120.02...Ti 0.06–0.10
T36K210010.10–0.170.80–1.200.0300.0250.25–0.501.00–1.300.300.25–0.500.02...0.015–0.0450.020.050...Cu 0.50–0.80
T91 K909010.07–0.140.30–0.60 0.020 0.010 0.20–0.50 0.40 8.0–9.50.85–1.050.18–0.25 ...0.06–0.100.030–
0.070		0.02...Ti 0.01
Zr 0.01
T92 K92460 0.07–0.13 0.30–0.60 0.020 0.010 0.500.40 8.5–9.5 0.30–0.600.15–0.25 0.001–
0.006		0.04–0.090.030–
0.070		0.021.5–2.00Ti 0.01
Zr 0.01
T122K912710.07–0.140.700.0200.0100.50 0.5010.0–11.50.25–0.600.15–0.300.0005–
0.005		0.04–0.100.040–
0.100		0.021.50–2.50Cu 0.30–1.70
Ti 0.01
Zr 0.01
T911K910610.09–0.130.30–0.600.0200.0100.10–0.500.408.5–9.50.90–1.100.18–0.250.0003–
0.006		0.06–0.100.040–
0.090		0.020.90–1.10Ti 0.01
Zr 0.01

A Maximum, unless range or minimum is indicated. Where ellipses (...) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. See 16.3.

C Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.

Committee
A 01
DocumentType
Standard
Pages
15
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

View more information
£70.87
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us