ASTM B 619/B619M : 2017 : REV A

Name: ASTM B 619/B619M : 2017 : REV A
Brand: ASTM
Price: 64.04 GBP

Superseded

View Superseded by

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

Available format(s)

Hardcopy , PDF

Superseded date

26-05-2023

Language(s)

English

Published date

16-08-2017

Publisher

American Society for Testing and Materials

1.1This specification2 covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06044; UNS N06058; UNS N06059; UNS N06200; UNS N10362; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N08034; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)3 as shown in Table 1.

TABLE 1 Chemical Requirements

Composition Limits, %
	Ni	Cr	Mo	Fe	W	C	Si max	Co	Mn	V	P max	S max	Ti	Cu	Cb (Nb) +Ta	Al	Zr	La	N	B	Cb (Nb)	Ta	Ni+ Mo	Mg
Ni-Mo Alloys
N10001	remainder^A	1.0 max	26.0- 30.0	4.0-6.0	...	0.05 max	1.0	2.5 max	1.0 max	0.2- 0.4	0.04	0.03	...	...	...
N10665	remainder^A	1.0 max	26.0- 30.0	2.0 max	...	0.02 max	0.10	1.0 max	1.0 max	...	0.04	0.03	...	...	...
N10675	65.0 min	1.0- 3.0	27.0- 32.0	1.0-3.0	3.0 max	0.01 max	0.10	3.0 max	3.0 max	0.20 max	0.030	0.010	0.20 max	0.20 max	...	0.50 max	0.10 max	...	...	...	0.20 max	0.20 max	94.0- 98.0
N10629	remainder^A	0.5- 1.5	26.0- 30.0	1.0-6.0	...	0.01 max	0.05	2.5 max	1.5 max	...	0.04	0.01	...	0.5 max	...	0.1- 0.5	...	...	...	...	...	...	...
N10624	remainder^A	6.0- 10.0	21.0- 25.0	5.0-8.0	...	0.01 max	0.10	1.0 max	1.0 max	...	0.025	0.01	...	0.5 max	...	...	...	...	...	...	...	...	...
Ni-Mo-Cr-Fe Alloy
N10242	remainder^A	7.0-9.0	24.0- 26.0	2.0 max		0.03 max	0.80	1.00 max	0.80 max		0.030	0.015		0.50 max		0.50 max				0.006 max
Low C Ni-Cr-Mo Alloys
N10276	remainder^A	14.5- 16.5	15.0- 17.0	4.0-7.0	3.0- 4.5	0.010 max	0.08	2.5 max	1.0 max	0.35 max	0.04	0.03	...	...	...
N06022	remainder^A	20.0- 22.5	12.5- 14.5	2.0-6.0	2.5- 3.5	0.015 max	0.08	2.5 max	0.5 max	0.35 max	0.02	0.02	...	...	...
N06035	remainder^A	32.25- 34.25	7.60- 9.00	2.00 max	0.60 max	0.050 max	0.60	1.00 max	0.50 max	0.20 max	0.030	0.015	...	0.30 max	...	0.40 max
N06044	balance	43.5- 45.3	0.80-1.20	0.3 max	...	0.02 max	0.20	...	0.07- 0.30	...	0.020	0.020	0.10- 0.30	...	...	0.30 max	...	...	...	...	...	...	...	...
N06058	balance	20.0- 23.0	18.5- 21.0	1.5 max	0.3 max	0.010 max	0.10 max	0.3 max	0.50 max		0.015	0.010	...	0.50 max	...	0.40 max			0.02- 0.15
N06059	balance	22.0- 24.0	15.0- 16.5	1.5 max	...	0.010 max	0.10	0.3 max	0.5 max	...	0.015	0.010	...	0.50 max	...	0.1- 0.4	...	...	...	...	...	...	...
N06455	remainder^A	14.0- 18.0	14.0- 17.0	3.0 max	...	0.015 max	0.08	2.0 max	1.0 max	...	0.04	0.03	0.70 max	...	...
Ni-Cr-Fe-Mo-Cu Alloys
N06007	remainder^A	21.0- 23.5	5.5- 7.5	18.0-21.0	1.0 max	0.05 max	1.0	2.5 max	1.0- 2.0	...	0.04	0.03	...	1.5- 2.5	1.75- 2.5
N06975	47.0-52.0	23.0- 26.0	5.0- 7.0	remainder	...	0.03 max	1.0	...	1.0 max	...	0.03	0.03	0.70- 1.50	0.70- 1.20	...
N06985	remainder^A	21.0- 23.5	6.0- 8.0	18.0-21.0	1.5 max	0.015 max	1.0 max	5.0 max	1.0 max	...	0.04	0.03	...	1.5- 2.5	0.50 max
N06030	remainder^A	28.0- 31.5	4.0- 6.0	13.0-17.0	1.5- 4.0	0.03 max	0.8	5.0 max	1.5 max	...	0.04	0.02	...	1.0- 2.4	0.30- 1.50
Ni-Fe-Cr-Mo Alloys
N08320	25.0-27.0	21.0- 23.0	4.0- 6.0	remainder	...	0.05 max	1.0	...	2.5 max	...	0.04	0.03	4xC min	...	...
Ni-Cr-Mo-Fe Alloy
N06002	remainder^A	20.5- 23.0	8.0- 10.0	17.0-20.0	0.20- 1.0	0.05- 0.15	1.0	0.5- 2.5	1.0 max	...	0.04	0.03	...	...	...
Ni-Fe-Cr-Co Alloy
R30556	19.0-22.5	21.0- 23.0	2.5- 4.0	remainder	2.0- 3.5	0.05- 0.15	0.20- 0.80	16.0- 21.0	0.50- 2.00	...	0.04	0.015	...	...	...	0.10- 0.50	0.001- 0.10	0.005- 0.10	0.10- 0.30	0.02 max	0.30 max	0.3- 1.25
Ni-Cr-W-Mo Alloy
N06230	remainder^A	20.0- 24.0	1.0- 3.0	3.0 max	13.0- 15.0	0.05- 0.15	0.25- 0.75	5.0 max	0.30- 1.00	...	0.03	0.015	...	...	...	0.50 max	...	0.005- 0.050	...	0.015 max	...	...
Low C-Ni-Cr-Mo-Cu Alloy
N06200	remainder^A	22.0- 24.0	15.0- 17.0	3.0 max	...	0.010 max	0.08	2.0 max	0.50 max	...	0.025	0.010	...	1.3- 1.9	...	0.50 max
Low-C-Ni-Mo-Cr Alloy
N10362	remainder^A	13.8- 15.6	21.5- 23.0	1.25 max	...	0.010 max	0.08	...	0.60 max	...	0.025	0.010	...	...	...	0.50 max	...	...	...	...	...	...	...	...
Low C-Ni-Fe-Cr-Mo-Cu Alloy
N08031	30.0-32.0	26.0- 28.0	6.0- 7.0	balance	...	0.015 max	0.3	...	2.0 max	...	0.020	0.010	...	1.0- 1.4	...	...	...	...	0.15- 0.25	...	...	...

N08034	33.5-35.0	26.0- 27.0	6.0-7.0	balance	...	0.01 max	0.1	...	1.0-4.0	...	0.020	0.010	...	0.5- 1.5	...	0.3 max	...	...	0.10- 0.25	...	...	...	...	...
Low C-Ni-Cr-Mo-W Alloy
N06686	remainder^A	19.0- 23.0	15.0- 17.0	5.0 max	3.0- 4.4	0.010 max	0.08	...	0.75 max	...	0.04	0.02	0.02- 0.25	...	...	...	...	...	...	...	...	...
Ni-Co-Cr-Si Alloy
N12160	remainder^A	26.0- 30.0	1.0 max	3.5 max	1.0 max	0.15 max	2.4- 3.0	27.0- 33.0	1.5 max	...	0.030	0.015	0.20- 0.80	...	...	...	...	...	...	...	1.0 max	...	...	...
Cr-Ni-Fe-N Alloy
R20033	30.0-33.0	31.0- 35.0	0.50- 2.0	balance	...	0.015 max	0.50†	...	2.0 max	...	0.02	0.01	...	0.3- 1.20	...	...	...	...	0.35- 0.60	...	...	...	...	...
Low C-Ni-Mo-Cr-Ta Alloy
N06210	remainder^A	18.0- 20.0	18.0- 20.0	1.0 max	...	0.015 max	0.08	1.0 max	0.5	0.35 max	0.02	0.02	...		...		...	...	...	...	...	1.5- 2.2

(A)The composition of the remainder shall be determined arithmetically by difference.

1.2This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size and larger as set forth in ANSI B36.19 (see Table 2).

TABLE 2 Dimensions of Welded Pipe

Note 1:The following table is a partial reprint of Table 1 of ANSI B36.19.

Note 2:The decimal thickness listed for the respective pipe sizes represents their nominal or average wall dimensions.

Nominal Pipe Size,	Outside Diameter		Nominal Wall Thickness
Nominal Pipe Size,	Outside Diameter		Schedule 5S^A		Schedule 10S^A		Schedule 40S		Schedule 80S
in.	in.	[mm]	in.	[mm]	in.	[mm]	in.	[mm]	in.	[mm]
¹/₈	0.405	10.29	...	...	0.049	1.24	0.068	1.73
¹/₄	0.540	13.72	...	...	0.065	1.65	0.088	2.24
³/₈	0.675	17.15	...	...	0.065	1.65	0.091	2.31
¹/₂	0.840	21.34	0.065	1.65	0.083	2.11	0.109	2.77
³/₄	1.050	26.67	0.065	1.65	0.083	2.11	0.113	2.87
1.0	1.315	33.41	0.065	1.65	0.109	2.77	0.133	3.38
1¹/₄	1.660	42.16	0.065	1.65	0.109	2.77	0.140	3.56
1¹/₂	1.900	48.26	0.065	1.65	0.109	2.77	0.145	3.68
2	2.375	60.33	0.065	1.65	0.109	2.77	0.154	3.91	0.218	5.54
2¹/₂	2.875	73.03	0.083	2.11	0.120	3.05	0.203	5.16	0.276	7.01
3	3.500	88.90	0.083	2.11	0.120	3.05	0.216	5.33
3¹/₂	4.000	101.60	0.083	2.11	0.120	3.05	0.226	5.74
4	4.500	114.30	0.083	2.11	0.120	3.05	0.237	6.02
5	5.563	141.30	0.109	2.77	0.134	3.40	0.258	6.55
6	6.625	168.28	0.109	2.77	0.134	3.40	0.280	7.11
8	8.625	219.18	0.109	2.77	0.148	3.76	0.322	8.18

(A)Schedules 5S and 10S wall thicknesses do not permit threading in accordance with ANSI B2.1-1960.

1.3Two classes of pipe are covered as follows:

1.3.1Class I—As welded and solution annealed or welded and sized and solution annealed.

1.3.2Class II—Welded, cold worked, and solution annealed.

1.4All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.

1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	B 02
DocumentType	Standard
Pages	6
PublisherName	American Society for Testing and Materials
Status	Superseded
SupersededBy	ASTM B 619/B619M : 2017 : REV B ASTM B 619/B619M : 2017B
Supersedes	ASTM B 619/B619M : 2017 ASTM B 619/B619M : 2017

ASTM B 366/B366M : 2023	Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
ASTM B 775/B775M : 2022	Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe