ASTM B 750 : 2016 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for GALFAN
Available format(s)
PDF
Superseded date
18-06-2022
Language(s)
English
Published date
26-07-2016
CONTAINED IN VOL. 02.04, 2016 Defines GALFAN, zinc-5% aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510) in ingot form for remelting for use in the production of hot-dip coatings on steel.
1.1This specification covers GALFAN, zinc-5 % aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510)3 in ingot form for remelting for use in the production of hot-dip coatings on steel. Alloy composition is specified in Table 1.
(A)For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures, used in expressing the specified limit, in accordance with the rounding procedure prescribed in Section 3 of Practice E29.
(B)By agreement between purchaser and supplier, analysis may be required and limits established for elements or compounds not specified in the table of chemical composition.
(C)GALFAN, Zn-5Al-MM alloy ingot for hot-dip coatings may contain antimony, copper, and magnesium in amounts of up to 0.002, 0.1, and 0.05 %, respectively. No harmful effects have ever been noted due to the presence of these elements up to these concentrations and, therefore, analyses are not required for these elements.
(D)Magnesium may be specified by the buyer up to 0.1 % maximum.
(E)Zirconium and titanium may each be specified by the buyer up to 0.02 % maximum.
(F)Aluminum may be specified by the buyer up to 12 % maximum.
(G)Lead and cadmium, and to a lesser extent tin and antimony, are known to cause intergranular corrosion in zinc-aluminum alloys. For this reason it is important to maintain the levels of these elements below the limits specified.
(H)Except antimony, copper, magnesium, zirconium, and titanium.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
| Committee |
B 02
|
| DocumentType |
Redline
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| 08/30189622 DC : 0 | BS EN 10223-8 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 8: WELDED MESH GABION PRODUCTS |
| ASTM A 856/A856M : 2003 : R2014 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Carbon Steel Wire |
| ASTM B 958 : 2008 | Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc<span class='unicode'>–</span>5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors |
| RR-F-191-1 Revision F:2008 | FENCING, WIRE AND POST METAL (CHAIN-LINK FENCE FABRIC) |
| ASTM B 802/B802M : 2010 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR) |
| ASTM B 802/B802M : 2010 : R2016 | Standard Specification for Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR) |
| ASTM A 855/A855M : 2003 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Wire Strand |
| ASTM A 1076/A1076M : 2013 | Standard Specification for Cold Formed Carbon Structural Steel Tubing Made from Metallic Precoated Sheet Steel |
| ASTM A 854/A854M : 2008 : R2017 | Standard Specification for Metallic-Coated Steel Smooth High-Tensile Fence and Trellis Wire |
| EN 10244-2:2009 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings |
| ONORM EN 10244-2 : 2009 | STEEL WIRE AND WIRE PRODUCTS - NON-FERROUS METALLIC COATINGS ON STEEL WIRE - PART 2: ZINC OR ZINC ALLOY COATINGS |
| AASHTO M 181 :2010 | SPECIFICATION FOR CHAIN-LINK FENCE |
| 08/30189607 DC : 0 | BS EN 10223-3 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 3: HEXAGONAL STEEL WIRE NETTING FOR ENGINEERING PURPOSES |
| ASTM A 855/A855M : 2003 : R2009 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Wire Strand |
| ASTM A 741 : 2011 : EDT 1 | Standard Specification for Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail |
| ASTM A 764 : 2007 : R2017 | Standard Specification for Metallic Coated Carbon Steel Wire, Coated at Size and Drawn to Size for Mechanical Springs |
| ASTM A 764 : 2007 | Standard Specification for Metallic Coated Carbon Steel Wire, Coated at Size and Drawn to Size for Mechanical Springs |
| ASTM A 925 : 2003 : R2014 | Standard Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Overhead Ground Wire Strand |
| ASTM A 854/A854M : 2008 : R2013 | Standard Specification for Metallic-Coated Steel Smooth High-Tensile Fence and Trellis Wire |
| ASTM A 875/A875M : 2013 : REDLINE | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
| ASTM A 1072/A1072M :2011 | Standard Specification for Zinc-5 % Aluminum (Hot-Dip) Coatings on Iron and Steel Products |
| I.S. EN 10244-2:2009 | STEEL WIRE AND WIRE PRODUCTS - NON-FERROUS METALLIC COATINGS ON STEEL WIRE - PART 2: ZINC OR ZINC ALLOY COATINGS |
| 05/30128482 DC : DRAFT JAN 2005 | ISO 7989-2 - STEEL WIRE AND WIRE PRODUCTS - NON-FERROUS METALLIC COATINGS ON STEEL WIRE - PART 2: ZINC OR ZINC-ALLOY COATING |
| RR-F-191-4 Revision F:2008 | FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE ACCESSORIES) |
| AASHTO M 30 : 2015 | SPECIFICATION FOR METALLIC-COATED STEEL WIRE ROPE AND FITTINGS FOR HIGHWAY GUARDRAIL |
| ASTM A 1007 : 2015 : REDLINE | Standard Specification for Carbon Steel Wire for Wire Rope |
| ISO 7989-2:2007 | Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc-alloy coating |
| ASTM A 817 : 2012 : R2017 | Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire |
| ASTM B 997 : 2016 : REDLINE | Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings |
| ASTM A 741 : 2011 : R2016 | Standard Specification for Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail |
| ASTM A 925 : 2003 : R2009 : EDT 1 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Overhead Ground Wire Strand |
| ASTM A 817 : 2012 | Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire |
| DIN EN 10244-2:2009-08 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings |
| UNI EN 10244-2 : 2009 | STEEL WIRE AND WIRE PRODUCTS - NON-FERROUS METALLIC COATINGS ON STEEL WIRE - PART 2: ZINC OR ZINC ALLOY COATINGS |
| AASHTO M 181 : 2010 : R2015 | SPECIFICATION FOR CHAIN-LINK FENCE |
| PREN 10223-3 : DRAFT 2008 | STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 3: HEXAGONAL STEEL WIRE MESH PRODUCTS FOR ENGINEERING PURPOSES |
| BS ISO 7989-2:2007 | Steel wire and wire products. Non-ferrous metallic coatings on steel wire Zinc or zinc-alloy coating |
| ASCE/SEI 19 16 : 2016 | STRUCTURAL APPLICATIONS OF STEEL CABLES FOR BUILDINGS |
| ASTM A 1072/A1072M : 2011 : R2015 | Standard Specification for Zinc-5 % Aluminum (Hot-Dip) Coatings on Iron and Steel Products |
| ASTM A 856/A856M : 2003 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Carbon Steel Wire |
| MIL-DTL-32488 Base Document:2014 | EXPEDITIONARY BARRIER SYSTEM (EBS) |
| ASTM A 741 : 2011 | Standard Specification for Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail |
| ASTM A 925 : 2003 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Overhead Ground Wire Strand |
| 08/30180144 DC : DRAFT JUNE 2008 | BS EN 10244-2 - STEEL WIRE AND WIRE PRODUCTS - NON-FERROUS METALLIC COATINGS ON STEEL WIRE - PART 2: ZINC OR ZINC ALLOY COATINGS |
| ASTM A 929/A929M : 2017-03 | SPECIFICATION FOR STEEL SHEET, METALLIC-COATED BY THE HOT-DIP PROCESS FOR CORRUGATED STEEL PIPE |
| ASTM B 803/B803M : 2008 : R2016 | Standard Specification for High-Strength Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors |
| ASTM A 854/A854M : 2008 | Standard Specification for Metallic-Coated Steel Smooth High-Tensile Fence and Trellis Wire |
| ASTM A 764 : 2007 : R2012 | Standard Specification for Metallic Coated Carbon Steel Wire, Coated at Size and Drawn to Size for Mechanical Springs |
| ASTM A 856/A856M : 2003 : R2009 | Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Carbon Steel Wire |
| ASTM A 855/A855M : 2003 : R2014 | Standard Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Wire Strand |
| ASTM B 803/B803M : 2008 : EDT 1 | Standard Specification for High-Strength Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors |
| BS EN 10244-2:2009 | Steel wire and wire products. Non-ferrous metallic coatings on steel wire Zinc or zinc alloy coatings |
| ASTM E 1277 : 2014 : REDLINE | Standard Test Method for Analysis of Zinc-5 % Aluminum-Mischmetal Alloys by ICP Emission Spectrometry |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ISO 3815-1:2005 | Zinc and zinc alloys Part 1: Analysis of solid samples by optical emission spectrometry |
| ISO 3815-2:2005 | Zinc and zinc alloys Part 2: Analysis by inductively coupled plasma optical emission spectrometry |
£55.10
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.