ASTM D 4703 : 2016 : REDLINE
Current
The latest, up-to-date edition.
Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
English
08-04-2016
CONTAINED IN VOL. 08.03, 2016 Defines the compression molding of thermoplastic granules and milled stock for the preparation of test specimens.
1.1This practice covers the compression molding of thermoplastic granules and milled stock for the preparation of test specimens.2
1.2While conditions for certain materials are given, the primary source of specific conditions shall be the material specification standards for each type of material.
1.3Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:The main body of this practice is equivalent to ISO 293-1986. Annex A1 and ISO 293-1986 differ in some details; however, specimens prepared using Annex A1, Procedure A should be equivalent to those prepared using ISO 293-1986, Cooling Method D. Specimens prepared using Annex A1, Procedure C should be equivalent to those prepared using ISO 293-1986, Cooling Method B. However, due to the greater cooling rate tolerances of the ISO standard, specimens prepared in accordance with ISO Cooling Method B may not be equivalent to Annex A1, Procedure C.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes ASTM D 1928, ASTM D 3010, ASTM D 3463 and ASTM D 647. (02/2002)
|
| DocumentType |
Redline
|
| Pages |
19
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| ASTM F 2018 : 2000 : EDT 1 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| CSA Z245.20-Z245.21 : 2006 | EXTERNAL FUSION BOND EPOXY COATING FOR STEEL PIPE/EXTERNAL POLYETHYLENE COATING FOR PIPE |
| ASTM D 3981 : 2009 : REV A | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 1784 : 2011 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
| ASTM D 1248 : 2016 : REDLINE | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM F 2922 : 2013 : R2018 | Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers |
| ASTM F 2922 : 2013 : EDT 1 | Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers |
| ASTM D 2103 : 2015 : REDLINE | Standard Specification for Polyethylene Film and Sheeting |
| ASTM F 2018 : 2000 : R2010 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens (Withdrawn 2019) |
| ASTM F 2947 : 2012 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2136 : 2018 : REDLINE | Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe |
| ASTM D 3981 : 2009 : REV A : R2016 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 7436 : 2017 : REDLINE | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM D 5885 : 2006 : R2012 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM D 3895 : 2014 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
| ASTM D 1998 : 2015 : REDLINE | Standard Specification for Polyethylene Upright Storage Tanks |
| ASTM D 2839 : 2016 : REDLINE | Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene |
| ASTM D 3004 : 2008 | Standard Specification for Crosslinked and Thermoplastic Extruded Semi-Conducting, Conductor and Insulation Shielding Materials |
| ASTM D 5575 : 2007 : R2013 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 5885 : 2006 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM D 955 : 2008 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
| AASHTO R 63 : 2013 | PRACTICE FOR SOLID WALL HIGH-DENSITY POLYETHYLENE (HDPE) CONDUIT FOR NON-PRESSURE APPLICATIONS USED FOR THE PROTECTION OF POWER AND TELECOMMUNICATIONS CABLES |
| CAN/CSA-B182.14-12/B182.15-12 | Profile steel reinforced polyethylene (SRPE) storm sewer pipe and fittings/Profile steel reinforced polyethylene (SRPE) sewer pipe and fittings |
| ASTM F 2947 : 2012 : EDT 1 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM D 955 : 2008 : R2014 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
| ASTM D 5885/D5885M : 2017 : REDLINE | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM F 3181 : 2016 | Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE |
| ASTM F 2617 : 2015 : REDLINE | Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry |
| ASTM D 3004 : 2008 : R2013 | Standard Specification for Crosslinked and Thermoplastic Extruded Semi-Conducting, Conductor and Insulation Shielding Materials |
| ASTM F 2018 : 2000 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| CSA B182.7 : 2006 | PSM TYPE MULTILAYER POLYVINYLCHLORIDE (PVC) SEWER PIPE HAVING REPROCESSED-RECYCLED CONTENT |
| ASTM F 2922 : 2013 | Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers |
| ASTM D 6247 : 2010 | Standard Test Method for Determination of Elemental Content of Polyolefins by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 8117 : 2017 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by Differential Scanning Calorimetry |
| CSA Z245.20 SERIES : 2014 | PLANT-APPLIED EXTERNAL COATINGS FOR STEEL PIPE |
| ASTM D 5575 : 2007 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 4635 : 2016 : REDLINE | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| B184 SERIES-17 | Polymeric subsurface stormwater management structures |
| AASHTO M 294 : 2015 | SPECIFICATION FOR CORRUGATED POLYETHYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| ASTM D 3981 : 2009 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM F 1473 : 2018 : REDLINE | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM F 2947/F2947M : 2014-03 | SPECIFICATION FOR 150 TO 1500 MM [6 TO 60 IN.] ANNULAR CORRUGATED PROFILE-WALL POLYETHYLENE (PE) PIPE AND FITTINGS FOR SANITARY SEWER APPLICATIONS |
| ASTM F 2018 : 2000 : R2006 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| NBR 15593 : 2008 | PRESSURIZED BURIED SYSTEMS FOR WATER DISTRIBUTION AND SEWER - REQUIREMENTS FOR FUSION WELDED POLYETHYLENE FITTINGS PE 80 AND PE 100 |
| NBR 15561 : 2016 AMD 1 2017 | POLYETHYLENE PIPE PE 80 AND PE 100 FOR WATER TRANSPORT AND SEWAGE UNDER PRESSURE - REQUIREMENTS |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ASTM D 1248 : 2016 : REDLINE | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.