BS 4147:1980

Superseded

View Superseded by

Specification for bitumen-based hot-applied coating materials for protecting iron and steel, including suitable primers where required

Available format(s)

Hardcopy , PDF

Superseded date

29-12-2006

Language(s)

English

Published date

31-10-1980

Publisher

British Standards Institution

Foreword
Cooperating organizations
Specification
Section one. General
1 Scope
2 References
3 Definitions
4 Types of bitumen-based coating material
5 Types of primer
Section two. Primers
6 Type A. Bitumen-based primer for cold application
7 Type B. Synthetic primer for cold application
8 Type C. Bitumen primer for hot application
Section three. Coating materials
9 Type 1. Unfilled coating materials
10 Type 2. Coating materials with inert non-fibrous
    fillers
11 Type 3. Coating materials with inert fibrous fillers
Section four. Packaging, marking, sampling
12 Packaging
13 Marking
14 Sampling
15 Effect of non-metallic materials on water quality
Appendices
A Determination of volatile matter
B Determination of filler content by ignition
C Determination of density at 25 deg C
D Determination of penetration
E Sag test
F Bend test
G Impact test
H Peel tests
J Preparation of steel surfaces for the tests given in
    appendices E to H
K Priming of steel surfaces for the tests given in
    appendices E to H
L Application of coating material for the test given
    in appendices E to H
M Recommendations on the use of coating materials
Tables
1 Characteristics of bitumen in type A primer
2 Characteristics of type A primer for cold
    application
3 Characteristics of type B primer for cold
    application
4 Characteristics of type 1 coating materials
5 Tests for type 1 coating materials
6 Characteristics of type 2 coating materials
7 Tests for type 2 coating materials
8 Characteristics of type 3 coating materials
9 Tests for type 3 coating materials
Figure
1 Mould for sample for density determination

Requirements for hot applied bitumen based materials, both unfilled and reinforced with inert powdered or fibrous fillers, which will provide protection against corrosion.

Committee	ISE/110
DevelopmentNote	Supersedes 77/13457 DC and 85/10042 DC (07/2005) Supersedes TS 10195A. (11/2005)
DocumentType	Standard
Pages	16
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS EN 10300:2005

BS 2000-170(1982) : 1982	METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - FLASH POINT BY THE ABEL APPARATUS (NON STATUTORY METHOD)
BS 2000-47(1983) : 1983	METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - SOLUBILITY OF BITUMINOUS BINDERS
BS 4232:1967	Specification for surface finish of blast-cleaned steel for painting
BS 2000-49(1983) : 1983	METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - PENETRATION OF BITUMINOUS MATERIALS
BS 3900-A6:1971	Methods of test for paints. Tests on liquid paints (excluding chemical tests). Determination of flow time by use of flow cups
BS 3416:1975	Specification for black bitumen coating solutions for cold application
BS 1796:1976	Method for test sieving
BS 534:1966	Specification for steel pipes, fittings and specials for water, gas and sewage
BS 4689:1980	Method for determination of flash and fire points of petroleum products: Cleveland open cup method
BS 2000-58(1983) : 1983	METHOD OF TEST FOR PETROLEUM AND ITS PRODUCTS - SOFTENING POINT OF BITUMEN (RING AND BALL)
BS CP2010-2(1970) : 1970	PIPELINES - PART 2: DESIGN AND CONSTRUCTION OF STEEL PIPELINES IN LAND