BS EN 61008-1 : 2012
Current
The latest, up-to-date edition.
RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBS) - PART 1: GENERAL RULES (IEC 61008-1:2010, MODIFIED)
Hardcopy , PDF
English
01-01-2012
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Characteristics of RCCBs
6 Marking and other product information
7 Standard conditions for operation in service
and for installation
8 Requirements for construction and operation
9 Tests
Annex A (normative) - Test sequence and number of samples
to be submitted for certification purposes
Annex B (normative) - Determination of clearances and creepage
distances
Annex C (normative) - Arrangement for the detection of the emission
of ionized gases during short-circuit tests
Annex D (normative) - Routine tests
Annex E (informative) - Void
Annex IA (informative) - Methods for determination of short-circuit
power-factor
Annex IB (informative) - Glossary of symbols
Annex IC (informative) - Examples of terminal designs
Annex IE (informative) - Follow-up testing program for RCCBs
Annex IF (informative) - SCPDs for short-circuit tests
Annex J (normative) - Particular requirements for RCCBs with
screwless type terminals for external copper conductors
Annex K (normative) - Particular requirements for RCCBs with
flat quick-connect terminations
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Annex ZB (normative) - Special national conditions
Annex ZC (informative) - A-deviations
Annex ZZ (informative) - Coverage of Essential
Requirements of EU Directives
Annex ZXX (Informative) - List of clauses that require retesting
Pertains to residual current operated circuit-breakers functionally independent of, or functionally dependent on, line voltage, for household and similar uses, not incorporating overcurrent protection (hereafter referred to as RCCBs), for rated voltages not exceeding 440 V a.c and rated currents not exceeding 125 A, for fixed installations intended principally for protection against shock hazard.
Committee |
PEL/23/1
|
DevelopmentNote |
Together with BS EN 61008-2-1 & BS IEC 1008-2.2, it supersedes BS4293(1983). Supersedes 88/22488 DC, 95/204384 DC, 97/202575 DC, 97/207742 DC, 97/207509 DC, 97/207743 DC, 03/307802 DC, 07/30162124 DC, 08/30176716 DC, 10/30237874 DC & 07/30169767 DC. 2012 Edition remains current and will be withdrawn on 04-08-2017. Supersedes 12/30272118 DC. 2012 + A2 2013 Edition remains active & will be withdrawn on 06/07/2018.Supersedes 15/30321812 DC. 2012 Edition Re-issued in April 2017 & incorporates AMD 12 2017. (04/2017)
|
DocumentType |
Standard
|
Pages |
170
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
|
Standards | Relationship |
NEN EN 61008-1 : 1995 AMD 11 1995 | Identical |
SN EN 61008-1 : 2012 AMD 12 2017 | Identical |
UNE-EN 61008-1:2013 | Identical |
IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV | Identical |
NBN EN 61008-1 : 2013 AMD 1/COR 16 | Identical |
I.S. EN 61008-1:2012&A1:2014/ac&A2:2014...A12:2017 | Identical |
EN 61008-1:2012/A12:2017 | Identical |
DIN EN 61008-1 : 2018 | Identical |
NF EN 61008-1 : 2013 AMD 12 2018 | Identical |
16/30337150 DC : 0 | BS 7288 - SPECIFICATION FOR RESIDUAL CURRENT DEVICES WITH OR WITHOUT OVERCURRENT PROTECTION FOR SOCKET-OUTLETS FOR HOUSEHOLD AND SIMILAR USES |
BS IEC 1008-2.2 : 1990 | SPECIFICATION FOR RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBS) - APPLICABILITY OF THE GENERAL RULES TO RCCBS FUNCTIONALLY DEPENDENT ON LINE VOLTAGE |
BS 7671(2008) : 2018 | REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS |
BS 7430:1998 | Code of practice for earthing |
BS 8450:2006 | Code of practice for installation of electrical and electronic equipment in ships |
11/30249994 DC : DRAFT JULY 2011 | BS 7430 - CODE OF PRACTICE FOR PROTECTIVE EARTHING OF ELECTRICAL INSTALLATIONS |
BS 7909:2011 | Code of practice for temporary electrical systems for entertainment and related purposes |
BS 7375:1996 | Code of practice for distribution of electricity on construction and building sites |
BS 7375:2010 | Distribution of electricity on construction and demolition sites. Code of practice |
BS 7909:1998 | Code of practice for design and installation of temporary distribution systems delivering a.c. electrical supplies for lighting, technical services and other entertainment related purposes |
08/30166535 DC : DRAFT MAR 2008 | BS 7909 - CODE OF PRACTICE FOR TEMPORARY ELECTRICAL SYSTEMS FOR ENTERTAINMENT AND RELATED PURPOSES |
11/30218915 DC : DRAFT JAN 2011 | BS 6164 - CODE OF PRACTICE FOR HEALTH AND SAFETY IN TUNNELING IN THE CONSTRUCTION INDUSTRY |
BS 7288:2016 | Specification for residual current devices with or without overcurrent protection for socket-outlets for household and similar uses |
14/30270861 DC : 0 | BS 4163 - HEALTH AND SAFETY FOR DESIGN AND TECHNOLOGY IN EDUCATIONAL AND SIMILAR ESTABLISHMENTS - CODE OF PRACTICE |
07/30016130 DC : 0 | BS 5974 - CODE OF PRACTICE FOR THE PLANNING, DESIGN, SETTING UP AND USE OF TEMPORARILY INSTALLED SUSPENDED ACCESS EQUIPMENT |
BS EN 61008-2-1:1995 | Specification for residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs). Applicability of the general rules to RCCBs functionally independent of line voltage |
09/30205684 DC : 0 | BS 7375 - CODE OF PRACTICE FOR DISTRIBUTION OF ELECTRICITY ON CONSTRUCTION AND BUILDING SITES |
07/30130630 DC : 0 | BS 7430 - CODE OF PRACTICE FOR EARTHING |
BS 7671(2008) : 2008 | REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS |
BS 4163:2007 | HEALTH AND SAFETY FOR DESIGN AND TECHNOLOGY IN SCHOOLS AND SIMILAR ESTABLISHMENTS - CODE OF PRACTICE |
BS 4163:2014 | Health and safety for design and technology in educational and similar establishments. Code of practice |
BS 6164:2001 | Code of practice for safety in tunnelling in the construction industry |
EN 60998-1:2004 | Connecting devices for low-voltage circuits for household and similar purposes - Part 1: General requirements |
IEC 60998-1:2002 | Connecting devices for low-voltage circuits for household and similar purposes - Part 1: General requirements |
EN 61543:1995/A2:2006 | RESIDUAL CURRENT-OPERATED PROTECTIVE DEVICES (RCDS) FOR HOUSEHOLD AND SIMILAR USE - ELECTROMAGNETIC COMPATIBILITY |
EN 60998-2-2:2004 | Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units |
EN 60228:2005 COR 2005 | CONDUCTORS OF INSULATED CABLES |
HD 588.1 : S1 AMD 1 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS |
EN 60947-1:2007/A2:2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014) |
WC 8:1988 | ETHYLENE-PROPYLENE-RUBBER-INSULATED WIRE AND CABLE FOR THE TRANSMISSION AND DISTRIBUTION OF ELECTRICAL ENERGY |
EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
ASTM B 172 : 2017 : REDLINE | Standard Specification for Rope-Lay-Stranded Copper Conductors Having Bunch-Stranded Members, for Electrical Conductors |
EN 60060-2:2011 | High-voltage test techniques - Part 2: Measuring systems |
IEC 60998-2-2:2002 | Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units |
IEC TR 60755:2008 | General requirements for residual current operated protective devices |
IEC 62640:2011+AMD1:2015 CSV | Residual current devices with or without overcurrent protection forsocket-outlets for household and similar uses |
EN 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
WC 3-1992 | RUBBER-INSULATED WIRE AND CABLE FOR THE TRANSMISSION AND DISTRIBUTION OF ELECTRICAL ENERGY |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
EN 60664-5:2007 | Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
EN 60664-3:2017 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
EN 60038 : 2011 | CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED) |
EN 55014-1:2017 | Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission |
EN 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014) |
WC 7-1988 | CROSS-LINKED-THERMOSETTING-POLYETHYLENE-INSULATED WIRE AND CABLE FOR THE TRANSMISSION AND DISTRIBUTION OF ELECTRICAL ENERGY |
EN 60269-1:2007/A2:2014 | LOW-VOLTAGE FUSES - PART 1: GENERAL REQUIREMENTS (IEC 60269-1:2006/A2:2014) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.