Name: CEN/TS 1948-5:2015
Brand: CEN

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 5: Long-term sampling of PCDDs/PCDFs and PCBs

Published date

01-04-2015

Publisher

Comite Europeen de Normalisation

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Principle of long-term PCDD/PCDF/PCB sampling
6 Sampling device and materials
7 Minimum requirements for long-term PCDD/PCDF/PCB
   sampling methods
8 Quality assurance
9 Analytical procedure
10 Estimation of uncertainty of the method
11 Reporting
Annex A (normative) - Overview of minimum requirements
Annex B (informative) - Cleaning of the probe
Annex C (normative) - Performance criteria and test procedure
        for certification
Annex D (informative) - Examples of devices and operation for
        long-term sampling systems
Annex E (informative) - Fundamentals of isokinetic sampling
Annex F (informative) - Example for the determination of the
        representative sampling point
Annex G (informative) - Estimation of the uncertainty of
        measured PCDD/PCDF of the long-term sampling
        system
Annex H (informative) - Example for calculation of measurement
        results for standard conditions
Annex I (normative) - Adaption of the maximum deviation in
        relation to the PCDD/PCDF/PCB concentration
Bibliography

This Technical Specification CEN/TS 1948-5 specifies the long-term sampling of PCDD/PCDF/PCB concentrations in emissions of stationary sources. It is intended to base the new method on EN 1948 Part 2, 3, 4 "Analyses of PCDD/PCDF/PCB". The development of the new method is necessary due to the enhanced demand of several European countries and of the European Commission with regard to possible amendment of the Waste Incineration Directive 2000/76.http://ec.europa.eu/environment/air/stationary.htm#2http://ec.europa.eu/environment/air/pdf/technical_annex2.pdfPreferably the development of the method has to be done by validation measurements.

Committee	CEN/TC 264
DocumentType	Technical Specification
PublisherName	Comite Europeen de Normalisation
Status	Current

Standards	Relationship
PD CEN/TS 1948-5:2015	Identical
DIN CEN/TS 1948-5;DIN SPEC 33970:2015-06	Identical
DIN CEN/TS 1948-5;DIN SPEC 33970:2015-06	Identical
S.R. CEN/TS 1948-5:2015	Identical
UNI CEN/TS 1948-5 : 2015	Identical
XP CEN/TS 1948-5 : 2015 XP	Identical
NEN NPR CEN/TS 1948-5 : 2015	Identical

ISO/IEC 17025:2005	General requirements for the competence of testing and calibration laboratories
EN 15267-3:2007	Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources
EN 1948-2:2006	Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 2: Extraction and clean-up of PCDDs/PCDFs
ISO 14956:2002	Air quality Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty
EN ISO 16911-1:2013	Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 1: Manual reference method (ISO 16911-1:2013)
EN 15267-2:2009	Air quality - Certification of automated measuring systems - Part 2: Initial assessment of the AMS manufacturer’s quality management system and post certification surveillance for the manufacturing process
EN 15259:2007	Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
ISO/IEC Guide 99:2007	International vocabulary of metrology Basic and general concepts and associated terms (VIM)
EN 13284-1:2017	Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method
ISO 16911-1:2013	Stationary source emissions — Manual and automatic determination of velocity and volume flow rate in ducts — Part 1: Manual reference method
EN 14181:2014	Stationary source emissions - Quality assurance of automated measuring systems
EN 1948-1:2006	Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 1: Sampling of PCDDs/PCDFs
EN 1948-3:2006	Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 3: Identification and quantification of PCDDs/PCDFs
EN ISO 14956 : 2002	AIR QUALITY - EVALUATION OF THE SUITABILITY OF A MEASUREMENT PROCEDURE BY COMPARISON WITH A REQUIRED MEASUREMENT UNCERTAINTY
ENV 13005 : DRAFT 1999	GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT
EN 1948-4:2010+A1:2013	STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF PCDDS/PCDFS AND DIOXIN-LIKE PCBS - PART 4: SAMPLING AND ANALYSIS OF DIOXIN-LIKE PCBS
EN 15267-1:2009	Air quality - Certification of automated measuring systems - Part 1: General principles