DIN EN 60928 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
AUXILIARIES FOR LAMPS - A.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS - GENERAL AND SAFETY REQUIREMENTS
01-12-2001
12-01-2013
Vorwort
Einleitung
Hauptabschnitt 1 - Allgemeine Anforderungen
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Allgemeine Anforderungen
5 Allgemeines über die Prüfungen
6 Einteilung
7 Aufschriften
Hauptabschnitt 2 - Sicherheitsanforderungen
8 Anschlussklemmen
9 Schutzleiteranschluss
10 Kriech- und Luftstrecken
11 Schutz gegen zufällige Berührung mit aktiven Teilen
12 Schutz dazugehöriger Bauteile
13 Feuchtebeständigkeit und Isolierung
14 Spannungsfestigkeit
15 Anomale Bedingungen
16 Fehlerbedingungen
17 Schrauben, stromführende Teile und Verbindungen
18 Wärmebeständigkeit und Feuerbeständigkeit
19 Beständigkeit gegen Korrosion
Bilder
Anhang A (normativ) Prüfung zur Bestimmung, ob ein
leitfähiges Teil als aktives Teil anzusehen
ist, das einen elektrischen Schlag verursachen
kann
Anhang B (normativ) Besondere Anforderungen an
elektronische Vorschaltgeräte mit
Schutzvorrichtungen gegen Überhitzung
Anhang C (normativ) Besondere zusätzliche Anforderungen
an die Sicherheit für
wechselstrom-/gleichstromversorgte
elektronische Vorschaltgeräte für Notbeleuchtung
in Dauerschaltung
Anhang D (normativ) Messung des hochfrequenten
Ableitstromes
Anhang ZA (normativ) Andere in dieser Norm zitierte
internationale Publikationen mit den Verweisungen
auf die entsprechenden europäischen Publikationen
Describes general and safety requirements for electronic ballasts for use on a.c. supplies up to 1,000V at 50 Hz or 60 Hz with operating frequencies deviating from supply frequency, associated with tubular fluorescent lamps as described in IEC publication 81 and other tubular fluorescent lamps for high-frequency operation. Special requirements for electronic ballasts with protective devices against overheating are included.
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| I.S. EN 60928:1997 | Identical |
| NF EN 60928 : 96 AMD 1 2001 | Identical |
| SN EN 60928 : 1995 AMD 1 1999 | Identical |
| NBN EN 60928 : 95 AMD 1 2000 | Identical |
| EN 60928:1995/A1:1999 | Identical |
| IEC 60928:1995+AMD1:1999 CSV | Identical |
| VDE 0712-22 : 2000 | Corresponds |
| BS EN 60928:1995 | Identical |
| VDE 0712-22 : 2000 | Identical |
| VDE V 0161-231 : 1998 | AERONAUTICAL GROUND LIGHTING ELECTRICAL INSTALLATION - CONSTANT CURRENT REGULATOR - EQUIPMENT SPECIFICATIONS AND TESTS |
| VDE V 0161-235 : 1998 | AERONAUTICAL GROUND LIGHTING ELECTRICAL INSTALLATION - SIGNS - EQUIPMENT SPECIFICATIONS AND TESTS |
| VDE V 0161-234 : 1998 | Aviation ground lighting electric installation - Flashing lights Equipment specifications and tests; |
| DIN V ENV 50231 : 1998 | AERONAUTICAL GROUND LIGHTING ELECTRICAL INSTALLATION - CONSTANT CURRENT REGULATOR - EQUIPMENT SPECIFICATIONS AND TESTS |
| DIN EN 50021 : 2000 | ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - TYPE OF PROTECTION "N" |
| DIN V ENV 50235 : 1998 | AERONAUTICAL GROUND LIGHTING ELECTRICAL INSTALLATION - SIGNS - EQUIPMENT SPECIFICATIONS AND TESTS |
| DIN V ENV 50234 : 1998 | AERONAUTICAL GROUND LIGHTING ELECTRICAL INSTALLATION - FLASHING LIGHTS - EQUIPMENT SPECIFICATIONS AND TESTS |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| DIN EN 60317 : AMD 100 1998 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - AMENDMENT A100 TO PARTS OF THE DIN EN 60317 SERIES |
| IEC 60730-2-3:2006 | Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps |
| VDE 0631-2-3 : 2008-06 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
| HD 214 : 200S2 | RECOMMENDED METHOD FOR DETERMINING THE COMPARATIVE TRACKING INDEX OF SOLID INSULATING MATERIALS UNDER MOIST CONDITIONS |
| DIN EN 60081:2014-09 | DOUBLE-CAPPED FLUORESCENT LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60081:1997 + A1:2000, MODIFIED + A2:2003 + A3:2005 + A4:2010 + A5:2013) |
| EN 60920:1991/A11:2000 | BALLAST FOR TUBULAR FLUORESCENT LAMPS - GENERAL AND SAFETY REQUIREMENTS |
| DIN EN 60598-2-22 : 2015 COR 2 2017 | LUMINAIRES - PART 2-22: PARTICULAR REQUIREMENTS - LUMINAIRES FOR EMERGENCY LIGHTING (IEC 60598-2-22:2014) |
| DIN EN 60691 : 2017 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE (IEC 60691:2015 + COR1:2016) |
| VDE 0821 : 2017 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE (IEC 60691:2015 + COR1:2016) |
| DIN EN 60598-1 : 2015 COR 1 2016 | LUMINAIRES - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 60598-1:2014, MODIFIED) |
| DIN VDE 0470-1 : 1992 | |
| VDE 0711-1 : 2015 COR 1 2016 | LEUCHTEN - TEIL 1: ALLGEMEINE ANFORDERUNGEN UND PRUEFUNGEN (IEC 60598-1:2014, MODIFIZIERT) |
| DIN VDE 0110-3 : 1998 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATINGS TO ACHIEVE INSULATION COORDINATION OF PRINTED BOARD ASSEMBLIES |
| EN 60929:2011/A1:2016 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| IEC 60929:2011+AMD1:2015 CSV | AC and/or DC-supplied electronic control gear for tubularfluorescent lamps - Performance requirements |
| VDE 0471-2-11 : 2014 | FIRE HAZARD TESTING - PART 2-11: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY TEST METHOD FOR END-PRODUCTS (GWEPT) |
| DIN EN 60695-2-11 : 2014 | FIRE HAZARD TESTING - PART 2-11: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY TEST METHOD FOR END-PRODUCTS (GWEPT) |
| DIN EN 60695-2-2 : 1996 | FIRE HAZARD TESTING - PART 2: TEST METHODS - SECTION 2: NEEDLE-FLAME TEST |
| VDE 0303-1 : 1984 | METHOD FOR DETERMINING THE COMPARATIVE AND THE PROOF TRACKING INDICES OF SOLID INSULATING MATERIALS UNDER MOIST CONDITIONS |
| DIN 40101-1:1991-11 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT; GRAPHICAL SYMBOLS FOR IEC 417 |
| DIN EN 60730-2-3 : 2008-06 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| DIN EN 60929 : 2016 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS (IEC 60929:2011 + COR:2011 + A1:2015) |
| DIN EN 60920 : 1993 AMD 11 | BALLASTS FOR TUBULAR FLUORESCENT LAMPS - GENERAL AND SAFETY REQUIREMENTS |
| DIN EN 60901:2012-11 | SINGLE-CAPPED FLUORESCENT LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60901:1996 + A1:1997 + A2:2000 + A3:2004 + A4:2007 + A5:2011) |
| IEC 60901:1996+AMD1:1997+AMD2:2000 CSV | Single-capped fluorescent lamps - Performance specifications |
| DIN EN 60695-2-10 : 2014 | FIRE HAZARD TESTING - PART 2-10: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE APPARATUS AND COMMON TEST PROCEDURE (IEC 60695-2-10:2013) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| VDE 0711-2-22 : 2015 COR 2 2017 | LUMINAIRES - PART 2-22: PARTICULAR REQUIREMENTS - LUMINAIRES FOR EMERGENCY LIGHTING (IEC 60598-2-22:2014) |
| IEC 60691:2015 | Thermal-links - Requirements and application guide |
| VDE 0712-23 : 2016 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS (IEC 60929:2011 + COR.:2011 + A1:2015) |
| VDE 0712-10 : 93 AMD 11 2000 | BALLASTS FOR TUBULAR FLUORESCENT LAMPS; GENERAL AND SAFETY REQUIREMENTS |
| IEC 60598-1:2014+AMD1:2017 CSV | Luminaires - Part 1: General requirements and tests |
| EN 60730-2-3:2007 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| VDE 0471-2-10 : 2014 | FIRE HAZARD TESTING - PART 2-10: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE APPARATUS AND COMMON TEST PROCEDURE (IEC 60695-2-10:2013) |
| ISO 4046:1978 | Paper, board, pulp and related terms — Vocabulary |
| VDE 0715-7 : 1994 | LAMPS - SINGLE-CAPPED FLUORESCENT LAMPS; SAFETY AND PERFORMANCE REQUIREMENTS |
| IEC 60598-2-22:2014+AMD1:2017 CSV | Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting |
| IEC 60417C:1977 | Third supplement. |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| EN 60901:1996/A6:2017 | SINGLE-CAPPED FLUORESCENT LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60901:1996/A6:2014, MODIFIED) |
| DIN VDE 0303-1 : 1984 | METHOD FOR DETERMINING THE COMPARATIVE AND THE PROOF TRACKING INDICES OF SOLID INSULATING MATERIALS UNDER MOIST CONDITIONS |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| VDE 0106-102 : 2017 | METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT (IEC 60990:2016) |
| HD 243 : S12 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT - INDEX, SURVEY AND COMPILATION OF THE SINGLE SHEETS |
| EN 60695-2-2:1994/A1:1995 | FIRE HAZARD TESTING - TEST METHODS - NEEDLE-FLAME TEST |
| EN 60598-2-22:2014/AC:2016-09 | LUMINAIRES - PART 2-22: PARTICULAR REQUIREMENTS - LUMINAIRES FOR EMERGENCY LIGHTING (IEC 60598-2-22:2014/COR2:2016) |
| VDE 0471-2-2 : 1996 | FIRE HAZARD TESTING - PART 2: TEST METHODS; SECTION 2: NEEDLE-FLAME TEST |
| IEC 60920:1990 | Ballasts for tubular fluorescent lamps - General and safety requirements |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.