• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 12445:2000

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

INDUSTRIAL, COMMERCIAL AND GARAGE DOORS AND GATES - SAFETY IN USE OF POWER OPERATED DOORS - TEST METHODS

Available format(s)

Hardcopy , PDF

Superseded date

10-09-2017

Language(s)

English

Published date

01-01-2000

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

1 Scope
2 Normative references
3 Terms and definitions
4 Test method
  4.1 General
      4.1.1 Avoiding or safeguarding against
             crushing, shearing and drawing-in
             points
      4.1.2 Safeguarding against hazard or being
             lifted
      4.1.3 Safeguarding against impact hazards
  4.2 Drive unit and power supply
      4.2.1 Electrical drive unit
      4.2.2 Electrical equipment
      4.2.3 Additional requirements for hydraulic
             drive systems
      4.2.4 Additional requirements for pneumatic
             drive systems
      4.2.5 Controls
      4.2.6 Switching on of the drive
      4.2.7 Switching off of the drive
      4.2.8 Manual actuators
      4.2.9 Supply disconnecting device
      4.2.10 EMC
  4.3 Manual operation
  4.4 Additional hazards
      4.4.1 Pass doors
      4.4.2 Trapping
      4.4.3 Leaf travel limiting devices
      4.4.4 Unintended movements of the door leaf
      4.4.5 Interlocking
5 Force measuring method
  5.1 Measuring equipment
      5.1.1 Reference measuring equipment
      5.1.2 Measuring equipment for 'in situ'
             tests
  5.2 Points of measuring
      5.2.1 Sliding door
      5.2.2 Hinged swing door
      5.2.3 Folding door
      5.2.4 Vertically moving doors
      5.2.5 Barriers
6 Single fault failure
  6.1 Force limiting devices
  6.2 Other safeguarding devices
7 Testing method for presence detection
  7.1 Test pieces
  7.2 Testing of presence detection equipment to be
      used in conjunction with force limitation
      7.2.1 Testing of horizontal sliding and any
             type of vertically moving doors
      7.2.2 Testing of hinged and folding doors
      7.2.3 Testing of barriers
  7.3 Testing of presence detection system to be used
      without force limitation
      7.3.1 Testing of presence detection
             installed on the door leaf
      7.3.2 Testing of presence detection not
             installed on the door leaf
  7.4 Testing of presence detection in case of risk
      of being lifted
8 Test report

Defines the test methods to be applied to a power operated door to demonstrate compliance with the requirements specified in EN 12453:2000.

DocumentType
Standard
Pages
27
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
NF EN 12445 : 2001 Identical
EN 12445:2000 Identical
BS EN 12445:2001 Identical
DIN EN 12445:2001-02 Identical
NEN EN 12445 : 2000 Identical
NBN EN 12445 : 2001 Identical
NS EN 12445 : 1ED 2001 Identical
UNE-EN 12445:2001 Identical
UNI EN 12445 : 2002 Identical
SN EN 12445 : 2001 Identical

EN 50081-1:1992 Electromagnetic compatibility - Generic emission standard - Part 1: Residential, commercial and light industry
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
EN 12605:2000 Industrial, commercial and garage doors and gates - Mechanical aspects - Test methods
EN 12433-1:1999 Industrial, commercial and garage doors and gates - Terminology - Part 1: Types of doors
IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 12433-2:1999 Industrial, commercial and garage doors and gates - Terminology - Part 2: Parts of doors
EN 50081-2:1993 Electromagnetic compatibility - Generic emission standard - Part 2: Industrial environment
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN 50082-2 : 95 AC 95 ELECTROMAGNETIC COMPATIBILITY - GENERIC IMMUNITY STANDARD - INDUSTRIAL ENVIRONMENT
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
PREN 12978 : DRAFT 2017 INDUSTRIAL, COMMERCIAL AND GARAGE DOORS AND GATES - SAFETY DEVICES FOR POWER OPERATED DOORS AND GATES - REQUIREMENTS AND TEST METHODS
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 50082-1:1997 Electromagnetic compatibility - Generic immunity standard - Part 1: Residential, commercial and light industry

View more information
£54.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.