We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN 771-3:2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    SPECIFICATION FOR MASONRY UNITS - PART 3: AGGREGATE CONCRETE MASONRY UNITS (DENSE AND LIGHTWEIGHT AGGREGATES)

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-09-2015

    Language(s):  English

    Published date:  12-05-2011

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 Materials
    5 Requirements for aggregate concrete masonry units
    6 Description, designation and classification of aggregate
      concrete masonry units
    7 Marking
    8 Assessment and verification of constancy of performance
      (AVCP)'
    Annex A (normative) - Sampling for determination of
            product type and for independent testing of
            consignments'
    Annex B (normative) - Compliance criteria for product
            type determination and for independent testing
            of consignments'
    Annex C (informative) - Examples of different shapes
            of aggregate concrete masonry units
    Annex D (informative) - Guidance for test frequencies
            for designing a FPC system to demonstrate
            conformity of finished products with the
            requirements of the standard and the
            declaration of the manufacturer
    Annex ZA (informative) - Clauses of this European
             Standard addressing the provisions of the
             EU Construction Products Directive'
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the characteristics and performance requirements of aggregate concrete masonry units made from dense and lightweight aggregates or a combination of both for which the main intended uses are common, facing or exposed masonry in load bearing or non-load bearing building and civil engineering applications.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. 91, I.S. 189 & I.S. 190. (11/2010) Supersedes I.S. 20-1 & I.S. 20. (11/2011) 2011 Edition Re-Issued in September 2015 & incorporates AMD 1 2015. (09/2015)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    S.R. 325:2013+A2:2018/AC:2019 RECOMMENDATIONS FOR THE DESIGN OF MASONRY STRUCTURES IN IRELAND TO EUROCODE 6

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 998-2:2016 (edition 2) Specification for mortar for masonry - Part 2: Masonry mortar
    ISO 12491:1997 Statistical methods for quality control of building materials and components
    EN 772-2:1998/A1:2005 METHODS OF TEST FOR MASONRY UNITS - PART 2: DETERMINATION OF PERCENTAGE AREA OF VOIDS IN AGGREGATE CONCRETE MASONRY UNITS (BY PAPER INDENTATION)
    EN 772-1:2011+A1:2015 Methods of test for masonry units - Part 1: Determination of compressive strength
    EN 1745:2012 MASONRY AND MASONRY PRODUCTS - METHODS FOR DETERMINING THERMAL PROPERTIES
    ISO 12572:2016 Hygrothermal performance of building materials and products Determination of water vapour transmission properties Cup method
    EN 772-16:2011 Methods of test for masonry units - Part 16: Determination of dimensions
    EN ISO 12572:2016 HYGROTHERMAL PERFORMANCE OF BUILDING MATERIALS AND PRODUCTS - DETERMINATION OF WATER VAPOUR TRANSMISSION PROPERTIES - CUP METHOD (ISO 12572:2016)
    EN 1996-1-1:2005+A1:2012 (edition 2) Eurocode 6 - Design of masonry structures - Part 1-1: General rules for reinforced and unreinforced masonry structures
    EN 772-20:2000/A1:2005 METHODS OF TEST FOR MASONRY UNITS - PART 20: DETERMINATION OF FLATNESS OF FACES OF MOSONRY UNITS
    EN 772-6 : 2001 Methods of test for masonry units - Part 6: Determination of bending tensile strength of aggregate concrete masonry units
    EN 1052-3:2002/A1:2007 METHODS OF TEST FOR MASONRY - PART 3: DETERMINATION OF INITIAL SHEAR STRENGTH
    EN 772-11:2011 Methods of test for masonry units - Part 11: Determination of water absorption of aggregate concrete, autoclaved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units
    EN 772-13 : 2000 METHODS OF TEST FOR MASONRY UNITS - PART 13: DETERMINATION OF NET AND GROSS DRY DENSITY OF MASONRY UNITS (EXCEPT FOR NATURAL STONE)
    EN 1052-2:2016/AC:2017 METHODS OF TEST FOR MASONRY - PART 2: DETERMINATION OF FLEXURAL STRENGTH
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective