JIS C 60695-11-2:2007
|
Fire hazard testing Part 11-2: Test flames - 1 kW nominal pre-mixed flame - Apparatus, confirmatory test arrangement and guidance
|
JIS C 60695-4:1999
|
Terminology concerning fire test
|
JIS C 60695-2-2:2000
|
Fire hazard testing Part 2: Test methods - Section 2 - Needle-flame test
|
JIS C 60068-2-49:1993
|
Basic environmental testing procedures Part 2: Tests Guidance to Test Kc: Sulphur dioxide test for contacts and connections Part 2: Tests Guidance to Test Kc: Sulphur dioxide test for contacts and connections
|
JIS C 60068-2-46:1993
|
Basic environmental testing procedures Part 2: Tests Guidance to Test Kd: Hydrogen sulphide test for contacts and connections
|
JIS C 60068-2-13:1989
|
This Japanese Industrial Standard specifies the low pressure tests performed at room temperature. Part 2: Tests, Test M: Low air pressure
|
JIS C 60695-5-2:1999
|
Part 5: Assessment of potential corrosion damage by fire effluent - Section 2: Guidance on the selection and use of test methodsFire hazard testing -- Part 5: Assessment of potential corrosion damage by fire effluent -- Section 2: Guidance on the selection and use of test methods
|
JIS C 60068-2-11:1989
|
Basic environmental testing procedures Part 2: Tests - Test Ka: Salt mist
|
JIS C 60695-2-13:2004
|
Fire hazard testing - Glow-wire ignitability test method for materials
|
JIS C 60068-2-32:1995
|
Environmental testing Part 2: Tests. Test Ed: Free fall
|
JIS C 60068-1:1993
|
Environmental testing Part 1: General and guidance
|
JIS C 60068-2-60:1999
|
Environmental testing Part 2: Tests - Test Ke: Flowing mixed gas corrosion test
|
JIS C 60068-3-1:1995
|
Background information, Section One - Cold and dry heat tests
|
JIS C 60695-2-4-0:1995
|
Fire hazard testing Part 2: Test methods - Section 4/sheet 0: Diffusion type and premixed type flame test methods
|
JIS C 60068-2-31:1995
|
Environmental testing Part 2: Tests. Test Ec: Drop and topple, primarily for equipment-type specimens
|
JIS C 60068-2-45:1995
|
Environmental testing procedures of electronic and electrical resistance to solvents (immersion in cleaning solvents)
|
JIS C 60695-2-11:2004
|
Fire hazard testing - Glow-wire flammability test method for end-products
|
JIS C 60068-2-7:1993
|
Basic environmental testing procedures Part 2: Tests -- Test Ga and guidance: Acceleration, steady state Part 2: Tests - Test Ga and guidance: Acceleration, steady state
|
JIS C 5063:1997
|
Preferred number series for resistors and capacitors
|
JIS C 60068-2-64:1997
|
Environmental testing Part 2: Test methods - Test Fh: Vibration, broad-band random (digital control) and guidance
|
JIS C 60068-2-41:1995
|
Environmental testing Part 2: Tests, Test Z/BM: Combined dry heat/low air pressure tests Part 2: Tests, Test Z/BM: Combined dry heat/low air pressure tests
|
JIS C 60068-2-28:1993
|
Environmental testing, Part 2: Tests - Guidance for damp heat tests
|
JIS C 60068-2-18:2007
|
Environmental testing -- Part 2-18: Tests -- Test R and guidance: Water Part 2-18: Tests - Test R and guidance: Water
|
JIS C 60695-5-1:1996
|
Fire hazard testing Part 5: Assessment of potential corrosion damage by fire effluent - Section 1: General guidance
|
JIS C 60068-2-20:1996
|
Basic environmental testing procedures Part 2: Tests. Test T: Soldering
|
JIS C 60068-2-21:2002
|
Environmental testing Part 2-21: Tests - Test U: Robustness of termination and integral mounting devices
|
JIS C 60068-2-50:1997
|
Basic environmental testing procedures Part 2: Tests Tests Z/Afc: Combined cold/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
|
JIS C 5260-1:1999
|
Potentiometers for use in electronic equipment Part 1: Generic specification
|
JIS C 0066:2001
|
Flammability of solid non-metallic materials when exposed to flame sources - List of test methods
|
JIS C 60695-7-1:1997
|
Fire hazard testing Part 7: Guidance on the minimization of toxic hazards due to fires involving electrotechnical products Section 1: General
|
JIS C 60068-2-54:1996
|
Environmental testing Part 2: tests. Test Ta: Soldering. Solderability testing by the wetting balance method
|
JIS C 60695-2-12:2004
|
Fire hazard testing - Glow-wire flammability test method for materials
|
JIS C 60068-2-47:2008
|
Environmental testing Part 2-47: Tests - Mounting of specimens for vibration, impact and similar dynamic tests
|
JIS C 60355:1993
|
An appraisal of the problems of accelerated testing for atmospheric corrosion
|
JIS C 60695-1-2:1993
|
Fire hazard testing Part 1: Guidance for the preparation of requirements and test specifications for assessing fire hazard of electerotechnical products Guidance for electronic components
|
JIS C 60695-1-3:1993
|
Fire hazard testing Part 1: Guidance for the preparation of requirements and test specifications for assessing fire hazard of electrotechnical products Guidance for use preselection procedures
|
JIS C 60068-2-40:1995
|
Environmental testing Part 2: Tests, Test Z/AM: Combined cold/low air pressure tests
|
JIS C 60068-2-56:1996
|
Environmental testing Part 2: Tests. Test Cb: Damp heat, steady state, primarily for equipment
|
JIS C 60068-2-53:1997
|
Basic environmental testing procedures Part 2: Tests Guidance to tests Z/AFc and Z/BFc: Combined temperature (cold and dry heat) and vibration (sinusoidal) tests
|
JIS C 60068-2-51:1997
|
Basic environmental testing procedures Part 2: Tests Tests Z/BFc: Combined dry heat/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
|
JIS C 0046:1993
|
Environmental testing Part 2: Test methods Test Eg: Impact, spring hammer
|
JIS C 60695-11-3:1997
|
Fire hazard testing Part 2: Test methods - Section 4/sheet 2: 500 W nominal test flames and guidance
|
JIS C 60068-2-42:1993
|
Basic environmental testing procedures Part 2: Tests Test Kc: Sulphur dioxide test for contacts and connections<br>
|
JIS C 60068-2-61:1996
|
Environmental testing Part 2: Test methods Test Z/ABDM: Climatic sequence
|
JIS C 60068-2-17:2001
|
Basic environmental testing procedures -- Part 2: Tests -- Test Q: Sealing Part 2: Tests - Test Q: Sealing
|
JIS C 60068-2-58:2006
|
Environmental Testing - Part 2: Tests - Test Td: Test Methods For Solderability, Resistance To Dissolution Of Metallization And To Soldering Heat Of Surface Mounting Devices (smd)
|
JIS C 60068-2-43:1993
|
Basic environmental testing procedures Part 2: Tests Test Kd: Hydrogen sulphide test for contacts and connections
|