|
UNI CEI EN ISO/IEC 17050-1 : 2010
|
CONFORMITY ASSESSMENT - SUPPLIER'S DECLARATION OF CONFORMITY - PART 1: GENERAL REQUIREMENTS |
|
ISO 12176-3:2011
|
Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 3: Operator's badge |
|
UNI EN 12106 : 1999
|
PLASTICS PIPING SYSTEMS - POLYETHYLENE (PE) PIPES - TEST METHOD FOR THE RESISTANCE TO INTERNAL PRESSURE AFTER APPLICATION OF SQUEEZE-OFF |
|
UNI EN ISO 9000 : 2005
|
QUALITY MANAGEMENT SYSTEMS - FUNDAMENTALS AND VOCABULARY |
|
CEI 64-8/7 : 2012
|
LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 7: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS |
|
ISO 10838-3:2001
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
|
UNI 10576 : 1996
|
GAS PIPELINES PROTECTION DURING UNDERGROUND WORKS |
|
UNI EN ISO 9001 : 2008
|
QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS |
|
UNI EN 1775 : 2007
|
GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
|
ISO 12176-4:2003
|
Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4: Traceability coding |
|
ISO 10838-2:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
|
ISO 10838-1:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
|
ISO 12176-1:2017
|
Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
|
UNI 9860 : 2006
|
GAS SERVICE PIPES - DESIGN, CONSTRUCTION, TESTING, OPERATION, MAINTENANCE AND REHABILITATION |
|
UNI 9737 : 2007
|
QUALIFICATION OF WELDERS OF PLASTICS: WELDERS OF POLYETHYLENE COMPONENTS AND/OR POLYPROPYLENE, FOR THE CONVEYANCE OF COMBUSTIBLE GASES, WATER AND/OR OTHER FLUIDS UNDER PRESSURE, USING THE PROCEDURES FOR CONTACT HEATING ELEMENTS AND ELECTROFUSION - COMPLEMENTARY INSTRUCTIONS FOR THE APPLICATION OF EN 13067 |
|
UNI 10967 : 2001
|
WELDING OF POLYETHYLENE PE 100 PIPES AND CONNECTIONS FOR GAS, WATER AND OTHER PRESSURE FLUIDS PIPELINES |
|
UNI/TR 11228 : 2007
|
PROTECTING STRUCTURES FOR BURIED GAS PIPES FOR INTERFERENCES WITH RAILWAYS, TRAMWAYS, ROADS, OTHER BURIED UTILITIES AND BUILDINGS |
|
UNI 10521 : 2012
|
WELDING OF PLASTIC MATERIALS - ELECTRO-FUSION WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES |
|
UNI 7131 : 2014
|
LPG PLANTS FOR DOMESTIC USE NOT FED BY A DISTRIBUTION NETWORK - DESIGN, INSTALLATION AND COMMISSIONING |
|
ISO 12176-2:2008
|
Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
|
ISO 11414:2009
|
Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
|
UNI EN 1555-2 : 2011
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
|
UNI EN 12007-1 : 2012
|
GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 1: GENERAL FUNCTIONAL REQUIREMENTS |
|
UNI EN 1555-3 : 2013
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
|
UNI EN 12007-2 : 2012
|
GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
|
UNI EN 1555-1 : 2011
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
|
UNI 11024 : 2003
|
QUALITY REQUIREMENTS FOR WELDING OF POLYETHYLENE PIPES FOR GAS, WATER AND OTHER PRESSURE FLUIDS PIPELINES |
|
UNI 10761 : 2012
|
COORDINATION OF WELDING, PIPE LAYING AND TEST ACTIVITIES FOR POLYETHYLENE TRANSMISSION LINES OF GASEOUS FUELS, WATER AND OTHER FLUIDS UNDER PRESSURE - TASKS AND RESPONSIBILITIES, REQUIREMENTS FOR TRAINING, QUALIFICATION AND CERTIFICATION OF PERSONNEL |
|
UNI 10520 : 2009
|
WELDING OF PLASTIC MATERIALS - HEATED TOOL BUTT WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES |
|
PREN ISO 11299-3 : DRAFT 2012
|
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11299-3:2011) |
|
UNI EN 10204 : 2005
|
METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS |
|
PREN ISO 11299-1 : DRAFT 2012
|
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 1: GENERAL (ISO 11299-1:2011) |
|
ISO 16241:2005
|
Notch tensile test to measure the resistance to slow crack growth of polyethylene materials for pipe and fitting products (PENT) |
|
UNI 9165 : 2004
|
GAS DISTRIBUTION NETWORKS - PIPEWORKS WITH MAXIMUM OPERATING PRESSURE UP TO 5 BAR - DESIGN, CONSTRUCTION, TESTING, OPERATION, MAINTENANCE AND REHABILITATION |
|
UNI EN 1555-5 : 2011
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
|
UNI CEI EN ISO/IEC 17050-2 : 2005
|
CONFORMITY ASSESSMENT - SUPPLIER'S DECLARATION OF CONFORMITY - PART 2: SUPPORTING DOCUMENTATION |
|
UNI EN 12007-4 : 2012
|
GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 4: SPECIFIC FUNCTIONAL REQUIREMENTS FOR RENOVATION |
|
UNI 10565 : 2008
|
FIELD WELDING MACHINES BY THE HEATED TOOL FOR POLYETHYLENE PIPES AND/OR FITTINGS BUTT JOINTS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES - CONSTRUCTION, TEST AND MAINTENANCE REQUIREMENTS, DOCUMENTATION |
|
ISO 13950:2007
|
Plastics pipes and fittings Automatic recognition systems for electrofusion joints |
|
UNI 10566 : 2013
|
ELECTROFUSION WELDING MACHINES AND AUXILIARY EQUIPMENT FOR POLYETHYLENE PIPES AND/OR FITTING JOINTS BY ELECTROWELDABLE CONNECTIONS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES CONSTRUCTION, TEST AND MAINTENANCE REQUIREMENTS, DOCUMENTATION |
|
ISO 11413:2008
|
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
|
UNI EN 12327 : 2012
|
GAS INFRASTRUCTURE - PRESSURE TESTING, COMMISSIONING AND DECOMMISSIONING PROCEDURES - FUNCTIONAL REQUIREMENTS |
|
UNI 9034 : 2004
|
GAS DISTRIBUTION PIPELINES WITH MAXIMUM OPERATING PRESSURE NOT EXCEEDING 0,5 MPA (5 BAR) - MATERIALS AND JOINING SYSTEMS |