ASTM B 211/B211M : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
Hardcopy , PDF
11-09-2023
English
02-06-2019
This specification2 covers rolled or cold-finished bar, rod, and wire in alloys (Note 1) and tempers as shown in Table 2 [Table 3].
1.1This specification2 covers rolled or cold-finished bar, rod, and wire in alloys (Note 1) and tempers as shown in Table 2 [Table 3].
Note 1:Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
Note 2:The term cold finished is used to indicate the type of surface finish, sharpness of angles, and dimensional tolerances produced by drawing through a die.
Note 3:See Specification B221 [B221M] for aluminum and aluminum-alloy extruded bars, rods, wire, shapes, and tubes; and Specification B316/B316M for aluminum and aluminum-alloy rivet and cold-heading wire and rods.
1.2Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent UNS alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
B 07
|
| DocumentType |
Standard
|
| Pages |
13
|
| ProductNote |
THIS STANDARD ALSO REFERS TO CEN EN 14242,AMS 2772,Fed. Std. No. 123
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM B 247 : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
| ASTM G 32 : 2016 : R2021 : EDT 1 | Standard Test Method for Cavitation Erosion Using Vibratory Apparatus |
| ASTM C 1802 : 2023 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM B 247M : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric) |
| ASTM F 468 : 2023 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use |
| ASTM E 3112/E3112M : 2020 | Standard Test Method for Ballistic-resistant Products and Shoot Packs |
| ASTM E 1251 : 2007 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
| ASTM B 557 : 2015 : R2023 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| ASTM B 557M : 2015 : R2023 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
| ASTM G 47 : 2020 | Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products |
| ASTM E 1004 : 2009 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM G 47 : 2022 | Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products |
| ASTM B 557M : 2002 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric] |
| ASTM E 1251 : 1994 : R1999 | Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge |
| ASTM E 716 : 2016 : R2021 : EDT 2 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM B 660 : 2021 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM E 1251 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
| ASTM E 716 : 2016 : R2021 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 221M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) |
| ASTM B 316/B316M : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| ASTM B 594 : 2019 : EDT 1 | Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products |
| ASTM B 221 : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM E 527 : 2023 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM E 1004 : 1999 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
| ASTM E 1004 : 2002 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
| ASTM E 716 : 2016 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 557 : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| ASTM E 527 : 2016 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM B 557M : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric] |
| ASTM B 660 : 2015 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM B 594 : 2019 | Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products |
| ASTM B 221M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) |
| ASTM E 1251 : 2004 | Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
| ASTM E 1004 : 2017 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
| ASTM B 557 : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| ASTM E 1251 : 2011 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
| ASTM E 290 : 2022 | Standard Test Methods for Bend Testing of Material for Ductility |
| ASTM B 557M : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
| ASTM E 716 : 2016 : R2021 : EDT 1 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 221M : 2005 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes [Metric] |
| ASTM B 221M : 2000 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes [Metric] |
| ASTM E 1251 : 2017 : REV A | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
| ASTM E 3061 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method) |
| ASTM E 290 : 2014 | Standard Test Methods for Bend Testing of Material for Ductility |
| ASTM B 221 : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM B 221 : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.