• There are no items in your cart

BS EN ISO 19901-3:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Petroleum and natural gas industries. Specific requirements for offshore structures Topsides structure
Available format(s)

Hardcopy , PDF

Superseded date

01-30-2024

Language(s)

English

Published date

12-31-2014

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Overall considerations
6 Design requirements
7 Actions
8 Strength and resistance of structural components
9 Structural systems
10 Materials
11 Fabrication, quality control, quality assurance
   and documentation
12 Corrosion control
13 Loadout, transportation and installation
14 In-service inspection and structural integrity management
15 Assessment of existing topsides structures
16 Reuse of topsides structure
Annex A (informative) - Additional information and guidance
Annex B (informative) - Example calculation of building
        code correspondence factor
Annex C (informative) - Regional information
Bibliography

Provides requirements for the design, fabrication, installation, modification and structural integrity management for the topsides structure for an oil and gas platform.

This part of ISO19901 gives requirements for the design, fabrication, installation, modification and structural integrity management for the topsides structure for an oil and gas platform. It complements ISO19902, ISO19903, ISO19904-1, ISO19905-1 and ISO19906, which give requirements for various forms of support structure. Requirements in this part of ISO19901 concerning modifications and maintenance relate only to those aspects that are of direct relevance to the structural integrity of the topsides structure.

The actions on (structural components of) the topsides structure are derived from this part of ISO19901, where necessary in combination with other International Standards in the ISO19901 series. The resistances of structural components of the topsides structure can be determined by the use of international or national building codes, as specified in this part of ISO19901. If any part of the topsides structure forms part of the primary structure of the overall structural system of the whole platform, the requirements of this part of ISO19901 are supplemented with applicable requirements in ISO19902, ISO19903, ISO19904-1, ISO19905-1 and ISO19906.

This part of ISO19901 is applicable to the topsides of offshore structures for the petroleum and natural gas industries, as follows:

  • topsides of fixed offshore structures;

  • discrete structural units placed on the hull structures of floating offshore structures and mobile offshore units;

  • certain aspects of the topsides of arctic structures.

This part of ISO19901 is not applicable to those parts of the superstructure of floating structures that form part of the overall structural system of the floating structure; these parts come under the provisions of ISO19904-1. This part of ISO19901 only applies to the structure of modules on a floating structure that do not contribute to the overall integrity of the floating structural system.

This part of ISO19901 is not applicable to the structure of hulls of mobile offshore units.

This part of ISO19901 does not apply to those parts of floating offshore structures and mobile offshore units that are governed by the rules of a recognized certifying authority and which are wholly within the class rules.

Some aspects of this part of ISO19901 are also applicable to those parts of the hulls of floating offshore structures and mobile offshore units that contain hydrocarbon processing, piping or storage.

This part of ISO19901 contains requirements for, and guidance and information on, the following aspects of topsides structures:

  • design, fabrication, installation and modification;

  • in-service inspection and structural integrity management;

  • assessment of existing topsides structures;

  • reuse;

  • decommissioning, removal and disposal;

  • prevention, control and assessment of fire, explosions and other accidental events.

This part of ISO19901 applies to structural components including the following:

  • primary and secondary structure in decks, module support frames and modules;

  • flare structures;

  • crane pedestal and other crane support arrangements;

  • helicopter landing decks (helidecks);

  • permanent bridges between separate offshore structures;

  • masts, towers and booms on offshore structures.

Committee
B/525/12
DevelopmentNote
Supersedes 07/30092995 DC. (01/2011) Supersedes 14/30300516 DC. (01/2015)
DocumentType
Standard
Pages
130
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN ISO 19901-3:2014 Identical
ISO 19901-3:2014 Identical

ISO 19901-6:2009 Petroleum and natural gas industries — Specific requirements for offshore structures — Part 6: Marine operations
ISO 19901-2:2017 Petroleum and natural gas industries Specific requirements for offshore structures Part 2: Seismic design procedures and criteria
API 2A WSD : 2014 PLANNING, DESIGNING, AND CONSTRUCTING FIXED OFFSHORE PLATFORMS - WORKING STRESS DESIGN
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 19900:2013 Petroleum and natural gas industries General requirements for offshore structures
API SPEC 4F : 2013 SPECIFICATION FOR DRILLING AND WELL SERVICING STRUCTURES
BS EN 1995-1-2:2004 Eurocode 5. Design of timber structures General - Structural fire design
ISO 12944-5:2007 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint systems
CSA S16 : 2014 DESIGN OF STEEL STRUCTURES
API 2V : 2004 DESIGN OF FLAT PLATE STRUCTURES
ISO 2394:2015 General principles on reliability for structures
BS EN 1993-1-9:2005 Eurocode 3. Design of steel structures Fatigue
ASCE 7 05 : 2006 MINIMUM DESIGN LOADS FOR BUILDINGS AND OTHER STRUCTURES
ISO 19903:2006 Petroleum and natural gas industries Fixed concrete offshore structures
ISO 19904-1:2006 Petroleum and natural gas industries Floating offshore structures Part 1: Monohulls, semi-submersibles and spars
BS EN 1993-1-1 : 2005 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
AISC 360 : 2016 SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS
ISO 19902:2007 Petroleum and natural gas industries Fixed steel offshore structures
ISO 19906:2010 Petroleum and natural gas industries Arctic offshore structures
API 4E : 3ED 88 SPECIFICATION FOR DRILLING AND WELL SERVICING STRUCTURES
ISO 2631-2:2003 Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 2: Vibration in buildings (1 Hz to 80 Hz)
BS EN 1993-3-1:2006 Eurocode 3. Design of steel structures Towers, masts and chimneys
ISO 2631-1:1997 Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements
BS EN 13852-1:2013 Cranes. Offshore cranes General-purpose offshore cranes
ISO 20340:2009 Paints and varnishes Performance requirements for protective paint systems for offshore and related structures
API 2A LRFD : 1993 RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS - LOAD AND RESISTANCE FACTOR DESIGN
AWS D1.1/D1.1M : 2015 STRUCTURAL WELDING CODE-STEEL
ISO 19901-5:2016 Petroleum and natural gas industries Specific requirements for offshore structures Part 5: Weight control during engineering and construction
ISO 834-1:1999 Fire-resistance tests Elements of building construction Part 1: General requirements
BS EN 1998-1 : 2004 EUROCODE 8: DESIGN OF STRUCTURES FOR EARTHQUAKE RESISTANCE - PART 1: GENERAL RULES, SEISMIC ACTIONS AND RULES FOR BUILDINGS
ISO 22899-1:2007 Determination of the resistance to jet fires of passive fire protection materials Part 1: General requirements
CAA CAP 437 : 2016 OFFSHORE HELICOPTER LANDING AREAS
ISO 19901-1:2015 Petroleum and natural gas industries Specific requirements for offshore structures Part 1: Metocean design and operating considerations
ISO 13702:2015 Petroleum and natural gas industries — Control and mitigation of fires and explosions on offshore production installations — Requirements and guidelines
BS EN 1999-1-1 : 2007 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES
ISO 19905-1:2016 Petroleum and natural gas industries — Site-specific assessment of mobile offshore units — Part 1: Jack-ups
ISO 6897:1984 Guidelines for the evaluation of the response of occupants of fixed structures, especially buildings and off-shore structures, to low-frequency horizontal motion (0,063 to 1 Hz)
BS EN 1995-1-1 : 2012 EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
BS EN 1993-1-2:2005 Eurocode 3. Design of steel structures General rules - Structural fire design
ISO 13626:2003 Petroleum and natural gas industries — Drilling and production equipment — Drilling and well-servicing structures
ICAO 7300 ANNEX 14 VOL.2 : 2013 ANNEX 14 TO THE CONVENTION ON INTERNATIONAL CIVIL AVIATION (ICAO 7300) - AERODROMES - VOLUME 2: HELIPORTS
NORSOK M 501 : REV 6 SURFACE PREPARATION AND PROTECTIVE COATING
NS 3472 : 2001 STEEL STRUCTURES - DESIGN RULES
NORSOK N 004 : REV 3 AC 2014 DESIGN OF STEEL STRUCTURES

View more information
US$383.32
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.