• There are no items in your cart

EN 14870-1:2011

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified)
Withdrawn date

12-31-2011

Published date

06-29-2011

Foreword
Introduction
1 Scope
2 Conformance
3 Normative references
4 Terms and definitions
5 Symbols and abbreviated terms
6 Designation
7 Pressure rating and design
8 Information that shall be supplied by the purchaser
9 Manufacturing
10 Testing and inspection
11 Inspection document
12 Marking
Annex A (normative) - Manufacturing procedure specification
Annex B (normative) - PSL 2S bends ordered for sour service
Bibliography

This European Standard specifies the technical delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.This European Standard is applicable to induction bends made from seamless and welded pipe of unalloyed or low-alloy steels.NOTEThese are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183.This European Standard specifies the requirements for the manufacture of two product specification levels (PSLs) of induction bend corresponding to product specification levels given for pipe in ISO 3183.This European Standard is not applicable to the selection of the induction bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements; see also ISO 3183:2007, Introduction.This European Standard is not applicable to pipeline bends made by other manufacturing processes.On-land supply systems used by the gas supply industry excluding gas infrastructure from the input of gas into the on-shore transmission network up to the inlet connection of gas appliances "are excluded from the scope of this standard.

Committee
CEN/TC 12
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Withdrawn

14/30294476 DC : 0 BS EN 448 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE
I.S. EN 448:2015 DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE
PREN 448 : DRAFT 2018 DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE
DIN EN 1993-4-3:2010-12 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
DIN EN 1594:2013-12 GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS
I.S. EN 1594:2013 GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS
I.S. EN 1993-4-3:2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
PREN 1594 : DRAFT 2013 GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS
DIN EN 448:2016-02 DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE
BS EN 1594:2013 Gas infrastructure. Pipelines for maximum operating pressure over 16 bar. Functional requirements
BS EN 1993-4-3:2007 Eurocode 3. Design of steel structures Pipelines
UNI EN 1993-4-3 : 2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
UNI EN 1594 : 2013 GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS
07/30165568 DC : 0 BS EN 448 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE
BS EN 14870-3:2006 Petroleum and natural gas industries. Induction bends, fittings and flanges for pipeline transportation systems Flanges
UNE-EN 1594:2014 Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
UNE-EN 448:2017 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
EN 1993-4-3:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)
EN 1594:2013 Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
EN 448:2015 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
13/30271116 DC : 0 BS EN 1594 - GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS
18/30368651 DC : 0 BS EN 448 - DISTRICT HEATING PIPES - BONDED SINGLE PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FACTORY MADE FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND A CASING OF POLYETHYLENE
BS EN 448:2015 District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene

ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations
ASTM A 435/A435M : 2017 : REDLINE Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates
ISO 15590-1:2009 Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 1: Induction bends
ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
NACE TM 02 84 : 2016 EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING
ISO 12094:1994 Welded steel tubes for pressure purposes Ultrasonic testing for the detection of laminar imperfections in strips/plates used in the manufacture of welded tubes
ASTM E 340 : 2015 : REDLINE Standard Practice for Macroetching Metals and Alloys
NACE TM 01 77 : 2016 LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS
ISO 9303:1989 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections
ISO 783:1999 Metallic materials Tensile testing at elevated temperature
ISO 3183:2012 Petroleum and natural gas industries Steel pipe for pipeline transportation systems
ISO 11496:1993 Seamless and welded steel tubes for pressure purposes Ultrasonic testing of tube ends for the detection of laminar imperfections
ASTM A 578/A578M : 2017 : REDLINE Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
ISO 15590-3:2004 Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 3: Flanges
ISO 7438:2016 Metallic materials Bend test
ISO 15156-2:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 13664:1997 Seamless and welded steel tubes for pressure purposes Magnetic particle inspection of the tube ends for the detection of laminar imperfections
ASTM E 797 : 2005 Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method
ISO 7539-2:1989 Corrosion of metals and alloys Stress corrosion testing Part 2: Preparation and use of bent-beam specimens
ISO 15590-2:2003 Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 2: Fittings
EN ISO 7539-2 : 1995 CORROSION OF METALS AND ALLOYS - STRESS CORROSION TESTING - PART 2: PREPARATION AND USE ON BENT-BEAM SPECIMEN (ISO 7539-2:1989)
ISO 10474:2013 Steel and steel products — Inspection documents
ISO 80000-1:2009 Quantities and units — Part 1: General
ISO 13665:1997 Seamless and welded steel tubes for pressure purposes Magnetic particle inspection of the tube body for the detection of surface imperfections
ISO 9764:1989 Electric resistance and induction welded steel tubes for pressure purposes Ultrasonic testing of the weld seam for the detection of longitudinal imperfections
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
EN ISO 148-1:2016 Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016)
ISO 10124:1994 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Ultrasonic testing for the detection of laminar imperfections
ISO 13663:1995 Welded steel tubes for pressure purposes Ultrasonic testing of the area adjacent to the weld seam for the detection of laminar imperfections
ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
ISO 12095:1994 Seamless and welded steel tubes for pressure purposes Liquid penetrant testing
ASTM E 92 : 2017 : REDLINE Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
EN ISO 7438:2016 Metallic materials - Bend test (ISO 7438:2016)
ISO 9305:1989 Seamless steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of transverse imperfections

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.